lens hood for helios 44 2 3d models

Lost the door for my Pentax DA * 50-135 Lens Hood. They are no longer available. When they were, the cost was ridiculous. I was able to print one in PLA and the sprayed it matte black. ... Fits well and is secure.

The lens hood for Canon's EF 50mm f/1.8 STM attaches securely to the camera mount itself. ...So far, it has only been thoroughly tested on crop sensor cameras but could potentially fit within the frame on full-frame models as well.

It's a camera hood designed for a Pentax DA 18-135mm lens. Works well, very happy with it! Does make quite a snug fit. ... Updated to allow it to be stowed in the other direction, added light trap on the internal section, and with a new pattern on the...

I finally discovered a compatible lens hood that perfectly suits the original GoPro Hero HD waterproof hard shell case, allowing my Phantom DJI to fly with flawless shutter results from direct sunlight exposure. This clever design features...

I'm thrilled with how it's turned out - the stopper ensures that the lens hood is securely attached to the camera, giving us peace of mind during operation. ... I printed this part in black PLA plastic, requiring no support structures to hold it in...

Customized version of https://www.thingiverse.com/thing:6086763 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=6086763

Couldn't find a filter holder that can use 100mm size filter for my Samyang 135mm lens hood. So, I rescaled it from the Corkin design and made the filter holder thicker so that it can latch on the lens hood more steadily. I then made the block size...

UPDATE: A two-part version is now available for flexible materials at [www.thingiverse.com/thing:2951107](https://www.thingiverse.com/thing:2951107) This lens hood is engineered for a precise fit in both mechanical and optical aspects, significantly...

However, its secure positioning is solely reliant on Art's design and the gentle friction provided by the soft inner coating on the hood as it comes into contact with the wider part of the lens. Given the age of these lenses, tilting them upwards...

Lens hood for the tiny Sony RX0. Prints in two pieces and glued. ...Hood slides from the top.

Hello, I designed a Lens Hood Caps for my Bronica ETRSI. ... This part goes on the Square lens hood for the Zenzanon 75mm EII

I like to do astrophotograhy from my balcony, because I am lazy, but I do have an annoying street lamp close by, so I wanted an additional lens hood with some flocking on the inside to minimize the effect of it for my for Skywatcher EvoStar 72ED. ...

I'm uncertain about other lenses that come with this hood or what other lens hoods it may fit. It could probably be scaled to fit other lenses and might require slight sanding to achieve a precise fit. ... The second image above showcases a sample I...

... $100. ...I used Inventor to design mine and printed it out on our school's 3D Printer, which is a MakerBot Replicator 2. The lens hood fits perfectly on my Canon 7D 28-135mm lens, and it should work just fine for any camera that uses a 28-135mm lens.

Replacement lens hood for the Lumix (MFT) system Panasonic-Leica 100-400mm zoom lens. Replacement is the same size as the original, and mounts the same way (normal or reversed to stow), except that the clamp has been redesigned to allow for single...

This is a specialized hood for the Eken H9R camera lens.

This is a very simple Lens Hood for the GoPros Other formats will follow

Just my design of a lens hood for a 77mm canon

Short introduction Had an old 28-80mm Nikon lens laying around which did not have a lens hood. So I decided to design one. I tried to imitate the original HB-20 as close as possible by using reference images I found on eBay.</p> <p><strong>About...

GoPro 49mm Filter Holder with Lens Hood.

+**Thickness of Hood's Mount** +**Length of Hood's Mount** +**If Lens Mount should be extended** +**Length of Rounded part of Hood:** if you opt for flat type hood – enter “0” Simply open the design in "Customizer"* to enter the required values. Or...

**Short introduction** Had an old 28-80mm Nikon lens laying around which did not have a lens hood. So I decided to design one. I tried to imitate the original HB-20 as close as possible by using reference images I found on eBay. **About...

I designed this small lens hood to help with the problem. It snaps on to the Raspberry Pi Camera Case designed by lab27. This works with the original design or any of the remixes that does not change the case. ... Print both parts, put them together,...

I designed this small lens hood to help with the problem. It snaps on to the <a href="https://www.thingiverse.com/thing:3121052">Raspberry Pi Camera Case designed by lab27</a>. ...This works with the original design or any of the remixes that do not...

A lens hood for the Sony 55mm F1.8. ...Remix the fusion files if you want to make your own custom hood. Category: Camera

... hood with eSun PetG filament. Furthermore, I utilized Slic3r Prusa edition's variable layer height feature to achieve an incredibly fine layer thickness in the threaded areas, while maintaining a standard .20 layer height for the rest of the print.

Exact proportioned and sized model of a Sony NEX Lens hood. ...Easily editable for other cameras, great for camera assemblies.

I designed this small lens hood to help with the problem. It snaps on to the <a href="https://www.thingiverse.com/thing:3121052" target="_new">Raspberry Pi Camera Case designed by lab27</a>. This works with the original design or any of the remixes...

This is a reinterpretation of https://www.thingiverse.com/thing:443442. ... It's crafted specifically for the NEW CANON 18-55 IS STM, which boasts a distinct hood mount featuring two contact strips in place of three.