leicht model

I got a package of 5 and when I opened them I found that the design had changed slightly and the material they used on the newer models was slightly thinner. The original clips were therefore a little sloppy. I adjusted the clips to fit the newer...

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 1 pattern_line_thickness = 20 stencil_pattern_element_shape = 3...

I suggest printing samples of just the top 20mm of each model to make sure they fit before printing the whole tower. 3rd UPDATE: I've added a calibration print. This is a small sample of how the two halves of the v2.5 towers fit together. You can use...

Since the build volume on the Prusas is relatively limited i decided to maximize the footprint of the stand for stability. As for the height, the 2 piece construction while theoretically takes more time to print, there is no need for support for the...

Generate and print your own, compatible with any existing threads!This model was designed in Fusion 360 and uses 3 required input parameters and standard Metric thread profile equations to generate a cap that will perfectly fit any of your threaded...

However, the aim was to get this iteration published in the meantime so it will probably be developed as an add-on unit.This future addition will thus enable illumination of the job in hand, be it soldering, 3D printing or anything else requiring...

No special settings except for the optional color change.I suggest setting also the infill and supports angles to 35 degrees so it matches the angle of the parts.If you also want to print the letters on the cover you can use the MMU2 (or equivalent...

 It is recommended to use MERV13 or higher for virus carrying particles. The fan is a Black & Decker 9in Mini Box Fan, Model BFB09W.CostAt the time of writing this the total cost is the same for each of the 3 versions as the different...

Ok, so i designed another one because the existing models didn't satisfy me. I also made another design myself previously, but i was still not happy. The reason is that i dont know how all the pumps are designed. - Why do some pumps have...

... broken and no one is going to fix it. Download files one at a time by clicking Download each time. ### My some other things: Category: 2D Art

 It is recommended to use MERV13 or higher for virus carrying particles. The fan is a Black & Decker 9in Mini Box Fan, Model BFB09W*.CostAt the time of writing this the total cost is the same for each of the 3 versions as the different...

... broken and no one is going to fix it. Download files one at a time by clicking Download each time. ### My some other things: Category: 2D Art

I designed this model for my daughter, who wanted a treasure chest to go with her pirate costume.  She wanted it to be “really big”, so this design utilizes the nearly the full volume of the MK3s to make three sections that bolt together.  It has an...

If the diameter of mounting holes is (slightly) different you can simply scale the entire model (all parts) in your favorite slicing app to make it fit (the only thing that cannot easily be scaled is the small enclosure for the BT-amplifier). ...

Some LED displays (3 digit, common anode, 0.4 inch, row pitch of 12.7mm) -Wenrun 12.7mm LTD040BUE-101A red CA -Wenrun 12.7mm LTD040BAG-101 green CA -SunLED 12.7mm DUY10A3-A yellow CA -SunLED 12.7mm DUG10A3 green CA -Luckylight 12.7mm KW3-401AVA...

This version is included for those that want to create a custom playing field using other materials.Other Printing NotesWhile I was able to get pretty good results printing the sidewalls without supports, I did get better results adding a couple of...

Depending on your printer tolerances, it may be more or less tight, but if everything lines up it should be no problem.Fasten the 3 screws at the "top" (in this orientation) once the spine is flush with the caseCHANGELOG2022-03-01 - Moved away from...

The "cylinder" rotates, and will index to set the drill guide sizes for any of the 6 holes. This version has a "cylinder" which is designed with holes that are 2mm, 3.6mm, 4.4mm, 5.2mm, 6.0mm and 6.8mm (which correspond to 5/64, 9/64, 11/64, 13/64,...

Extending the print head cable on this model is not unheard of, it is a common change made when upgrading this printer to a direct extruder. The portal cable (black) does not need to be extended, even for the extension kit for 50mm, as long as you...

...I propose some activities to do programming this robot: First goal: Making it move The first and basic activity could be to program and model their movement, to find the correct position sequence for each leg for a forward run. First step: assembly.

Knob channel.stl - channel knob, for 16 position rotary encoder, model unknown, mine was from professional 16-ch radio. 7. Antenna.stl - old-style, PRR mock antenna. 8. Antenna New.stl - new style, EZ-PRR mock antenna. 9. PTT Lemo Single.stl - PTT...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

This model includes both a solid and a honeycomb version whether you want to print a more authentic and traditional version of the warlock or if you want it to be more unique. I used absolutely bottom of the barrel parts to get this to a fully...

If this is true, the topography in this model is still extremely exaggerated to make it more noticeable, about 15% of the radius, giving the model an egg shape. The star-facing direction (since it is tidal locked) of every model in this post is the...

License ------- The "Arduino Nano NeoPixel Ring Base" models (.stl) are licensed under the [CC BY](https://creativecommons.org/licenses/by/4.0/) license by [Code and Make](https://codeandmake.com/). The "Arduino Nano NeoPixel Ring Base" code...

The springs I upgraded to where Integy RC Model T8087 Progressive Spring Set: https://www.amazon.com/gp/product/B00W3ZCX00/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 They are a bit longer but will allow for some preload tension if you want. The...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...