left handed scissors vs right handed 3d models

As simple as this thing is, it took me a good number of weeks to get it right. The dovetails alone were a bit or trial and error to get them sliding well enough, yet not being too loose. There were also several times when I thought it was done, and...

Print the diffusers with a slow print speed and right-side-up, with the diffuser base flat against the print bed. No supports were needed on my Creality CR-10 V2. Print in flexible white TPU to allow these to bend as you smush them against trees...

The MechancialTube_upperPart and MechanicalTube_zScrew are the most difficult parts to get exactly right, as the mechanical tube needs to be able to slide up and down to adjust the focus. Do not try to force the zScrew to turn as it may break. If...

Cereal boxes (or similar) have the right rigidity for the project but do not lend themselves to a printer. The template turns out to be a great tool. One does not have to be super accurate in tracing and cutting. It does take a lot time; but it is...

However, to get it just right, I created custom threads by copying the XML file for that profile and then modifying the 20mm portion of the 20mx1.5mm section. Here is the XML code for that section: <ThreadDesignation>M20x1.5</ThreadDesignation> ...

If not, go and set it up!Maybe also check the accelerations with the new weight of the carriage.As the nozzle moves forward with, you will have to set the new home offsets, don't forget it ;)Slicer configYes, we are done, right? ...Well, to get the...

I paced 8 across the front edge, 3 on each side, and 4 across the back.Key MapThe Key Map is essentially the same as TheAlternate and match the keycaps in the photos - these are the function keys:Fn+Q = resets the keyboard (no bootloader)Fn+R =...

I also went over a few iterations of the box until I felt that it was just right. The Box can now be nested into the lid, which prevents the lid from getting in the way or lost. Everything prints without support and even without infill; check the...

The cutting template is also with the STL.In order to get the connection to the right place via the screw cap in the middle of the IBC, I had to think of a solution, because unfortunately my arms are not 1.5 meters long. Two holders for neodymium...

Print the diffusers with a slow print speed and right-side-up, with the diffuser base flat against the print bed. No supports were needed on my Creality CR-10 V2. Print in flexible white TPU to allow these to bend as you smush them against trees...

no forces applied there and the transparency allows for ligting to be applied from the bottom (when done right this takes care of shadows falling on the background). As I also use an A4 white paper as background, the "yellowish" color of the...

PLA worked fine for the three demos we made. How to Bias the Hinges Post-PrintWhen you first take the model off the build plate, it isn't going to want to fold right away. You will need to go in and bend the panels (gently!) so that they begin to...

Fixed Part 01's right edge (from rear view). Combined parts for a 3 part print. Combined parts to a whole image for smaller prints. Remix of a Remix of Jace1969's 275cm Executor. Overall length @ 100% is 275cm. To Do: Design snug/snap fit nose...

I put the cylinder above the top right corner and set Layer Start X and Layer Start Y to a high number like 500. The customizer will add this automatically by default if you're creating a model with all the parts.</p> <hr/> <p>For the best looking...

- Locking mechanism assembly: The main "Mount_top_v1.1.stl" part features three critical openings: a square hole that goes through to the right side, a larger slot for inserting the metal rod during assembly, and a hole inside the mount where the rod...

It's flange distance is 81.6mm. Added M4 grip mount on right side of middle section as well. Added a new STL, the Goodman Zone grip, but remixed. Made the mount surface flat so that it fits better to the middle section. Top and bottom knob can be...

...Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work.Our puzzles are modeled using the open-source puzzlecad library.

I've also heard that the upper link upper mount holes aren't quite right and if you want to use them you'll need to change the link length.Update 02/16/17: Finally got around to trying to install. Seems to be some lower link clearance issues with the...

You must rotate dices 4, 5 and 6 of 1/4 of turn in the right directionIf you want to rotate the dice 5. You must rotate dices 5 and 8 of 1/4 of turn in the bottom direction</li><li>If you want to rotate the dice 1. You must rotate dice 1 of 1/4 of...

I added a 220V power connector, which is combined with a switch and a fuse, so it seemed to me to do it right. I did not remake the original power supply case, since it is used as a heatsink. Instead, I designed the hull in two halves, which are...

The one on the right (as I am facing it) is where I mounted my camera. I used an M3 screw and a nut to fasten the mount. That's it! You could apply some double-sided sticky tape to the mount to add extra hold if you desire, but I like to be able to...

Your 6 fixing holes will be in exactly the right place, first time, every time.I've since added two small stubs onto the template design so that it can also be used to gauge the correct distance away from any brackets or frames you might need to work...

I've left the MK3 version up if you choose to use 1 bearing. I also made some slight improvements to the clamp design. You'll note there are now some bushings with "tight" in the file name - these are slightly tighter on the internal clearance if...

I repeatedly installed the bearing to be snug enough that it would scratch the steering tube, then removed the bearing and sanded just to remove the scratch marks it left behind. This way the sanding wouldn't make the steerer egg-shaped. After...

-Cura bridging settings for printing stacks- If a 0.3mm, 1 layer, gap is left between parts as with the stack stls provided then bridging will be activated in Cura if enabled. This allows you to slow down the first layer of the next part and...

Notes: - I printed all the parts lying down with supports and the panels seem strong and turned out pretty well - I left the supports on the body panels to add strength and to provide a surface to mount inside panels like the old school vinyl on...

To prevent bending pinch the wire close to the guide and push just a small amount of wire at a time. Insert LED with positive (long) lead on the left side Pull LED flush [or bent at the desired angle] Pull leads across bare wire and crimp ...

An issue with too low wall thickness on hull middle in front left part of the lid interface was fixed - thanks San Xu for reporting this. An instruction about ESC placement was added into the manual. Update 17.03.2024 Supersprint V0.2: Some more...

They are ment to be snapped in and left in place.Door HandleI added a handle to the case for easy opening and closing. The door normally only stays shut when you lock the door so I added a 9x1 disc magnet to the top and bottom of the door and it...

If another dimension is needed, bigger or smaller, the model can be scaled on one axis.&nbsp;I use it for a MacBook Pro 16'' 2019 that is 16.2mm and added two 1mm adhesive foam sheets, one for each side, that added to approximately 18.2mm so it has...