lee reloading die 3d models

This will replace the usual lee lock die with a split ring lock die like the hornady ones. This is for the large series lee dies like the .577 snider dies. I've included 2 different variations. The big one which is a little beefier so it'll be...

... die. It might work if you put this on top of another lee powder measure riser. the lee dies use the funnel adapters that are screwed in as a positive flaring stop. the print orientation should be correct and use supports. ...i printed 100% infill.

... in a press. This model is intended solely for reference purposes. To support reloading manufacturers, consider purchasing Lee Precision products directly from them - they are an excellent company known for producing high-quality reloading equipment.

This calls for a Lee Load Master 5 hole turret outfitted with dies. The base boasts holes designed to firmly support the turret loaded with dies in position, ensuring stability throughout the printing process. Robust threads are used, which should...

Adapter to attach Lee Perfect Powder measure to the expanding die from Lee as well. Threads are both ANSI Unified Screw Threads, with the following measures:Adapter Inside (measure side): 0.6875in -- 11/16-12 UN. If this one is too loose, use 5/8-11...

... Theres 5 holes, so you can store you re-sizer, powder thru die, bullet thru die, bullet seat die, and crimper die.The cut out for the lee dropper, and case cutter etc. is helpful, and it holds my case gauge as well. ... I hope you find it useful!

This is a simple bullet feeder adapter fitting many bullet feeder dies, but specifically designed to couple the GPmax bullet feeder die with the standard lee tubes (the same used for the cases). Prining it with the larger side up and no support...

Introducing a customized large shell feeder, compatible with the Lee Loadmaster Progressive Reloading Press and specifically designed for the 45/70 Govt. case. This innovative design incorporates standard bolts, screws, and springs from smaller shell...

Holder for die set (Modeled after Lee LoadMaster) attachment features two designs. One is specifically designed for bench use with a designated spot for label placement. The other is a wall-mounted version that also includes space for labeling and...

This allows you to hang your dies, inside Lee breechlock bushing, on a standard pegboard. I printed it on its side with a brim and line supports. This is a remix of a design by TheGerman found here: https://www.thingiverse.com/thing:1665452. ... I...

Wall mounted tray for lee shell holders, hold 5 x Lee press and 5 x prime shell holders. ... Still need to print and test, so not sure if sizing and tolerances is 100% correct.

Here is the list of parts needed to upgrade your Lee Pro 1000 powder measure: * A laser or CNC-cut replacement for the existing acrylic or aluminum part * An M3 Pan Head Screw for secure attachment * A spare spring, easily procurable at...

I liked the Breech Lock Die Holder by a4andy921, but I felt it needed a lid.

I adjust a one-pound powder container to fit seamlessly onto the Lee press, effectively utilizing its capacity to capture stray bullets, empty cases, or discarded primers with precision. ... If any of my creative solutions have been instrumental in...

There are 5 die holders in the tray, for the (1) resizer (2) powder thru die (3) bullet feed die (4) bullet seating die and (5) crimp die.If you are not using the Breech Locks, your die will still fit, with whatever lock ring you are using to hold...

This tray is designed for reloading dies, specifically made for HORNADY dies with Lock-N-Load Bushings. If you need it for LEE Precision dies with or without breech lock rings, check out the other version I created. ...You can store your booklet at the...

One was that Lee powder through dies are typically for pistol calibers, and I am looking to use this for rifles - the original does not give a tight fit to the through die, it's a good fit but I prefer to create a single unit when done. As I have an...

One that lee powder through dies are typically for pistol calibers, I am looking to use this for rifles and the original does not give a tight fit to the through die, it's a good fit but I prefer to create a single unit when done. As I have a unused...

PRINT IN FREEFORM EXTERIOR/VASE MODE, ZERO OFFSET TOP/BOTTOM. ...THIS IS A SIMPLE FUNNEL DESIGNED TO FIT TIGHTLY INTO THE TOP PART OF THE LEE CHARGE-THRU DIE.

Neck bushings organizer, wall-mounted. For 308 and 6.5 Creedmoor bushings. One for each, and one for both. ...Posts are slightly angled upward so bushings don't fall off.

Lee loads all 2 bench mount die holder. Used the spare unused hole on the bench mount adaptor available at https://www.thingiverse.com/thing:4080314. Support Patreon at https://www.patreon.com/bigmrtong. Patreon Preview can be accessed through...

Normally you can't use a Lee sizing die on a Hornady AP Press, but with this you can. Although this current one is only for the .356 sizing ram. I will be creating another that will be more universal. ...If you don't have access to a printer you can...

Lee Load All 2 Bench Mount Die Holder. (Used the spare unused hole on the bench mount adaptor, https://www.thingiverse.com/thing:4080314). ... Support Patreon : https://www.patreon.com/bigmrtong Patreon Preview : https://tinyurl.com/bigmrtong...

Crafted to securely store and manage eight reloading dies at a time.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/7lj2NLfSywu

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/7lj2NLfSywu

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/7lj2NLfSywu

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4k0ojKEFVhp

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4k0ojKEFVhp

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/4k0ojKEFVhp