lee app press upgrades 3d models

LEE APP adapteur for classic bullet resizer I used https://www.thingiverse.com/thing:4222678 and https://www.thingiverse.com/thing:4232467

I adjust a one-pound powder container to fit seamlessly onto the Lee press, effectively utilizing its capacity to capture stray bullets, empty cases, or discarded primers with precision. ... If any of my creative solutions have been instrumental in...

Don't you hate it when you're happily popping primers on your Lee APP and the deprime kit suddenly explodes in your face, sending parts flying across your reloading room, all because you forgot to check it recently? Me too, friend, me too. That's why...

this is a bin bracket for the lee app. I used https://www.thingiverse.com/thing:3402447 as a base and modified from there. I printed at 100% infill to make it as strong as possible. My print I added a hex cut out on the backside to mount the bin...

Um bei der Lee App nicht ständig die Höhe des Case Feeders neu einstellen zu müssen habe ich hierfür eine eigene Variante mit austauschbaren Tubes gezeichnet. Dadurch muss der Feeder nur einmal eingestellt werden und zukünftig muss nur noch das...

Customized version of https://www.thingiverse.com/thing:4233822 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4233822

Customized version of https://www.thingiverse.com/thing:4236659 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4236659

Customized version of https://www.thingiverse.com/thing:4358977 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4358977

Customized version of https://www.thingiverse.com/thing:4236659 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4236659

Customized version of https://www.thingiverse.com/thing:4358977 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4358977

Customized version of https://www.thingiverse.com/thing:4358977 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4358977

Customized version of https://www.thingiverse.com/thing:4358977 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4358977

Lee C Press spacer / primer guide for decapping

I like to wall mount a lot of my reloading stuff. ...wanted a way to mount my Lee turret press I use occasionally.

I've dedicated this small press to disarming only the casings, using the universal Lee primer remover. ...The indentation on the right side is used to insert a metal strip that serves as an automatic ejection lever for the casing.

A design of a taller deflector for a Lee Precision single stage reloading press. The OEM one is much shorter and primers often fly over the OEM one. ... Simple design for this problem.

... the one there and the part doesn't fit. ...So I built one, which fits. I have a Lee 3-Hole Turret Press with no Auto Index and no primer feeder, so it spit the primers in all directions. ...With the Deflector in place, it now does what it should.

This is the work area lighting for the Lee Classic Turret press After printing, you need to glue part 1 and part 2 I used a 24V LED strip, but 12V is fine. The width of the tape should be no more than 10 mm, a wire with a cross section of 0.5 mm and...

This is a bullet feeder for sizing purposes on the Lee APP press. It's tailored specifically for 45 ACP, but may also work effectively with other close calibers. The design was created with my printer in mind, so you might need to adjust the slicer...

This is a bullet feeder designed specifically for the Lee APP press, used primarily for sizing purposes. It's optimized for 380 caliber, but may also function well with close calibers due to its versatile design. Since it was created with my own...

This is a bullet feeder for sizing purposes on Lee APP press. It is designed for 32 caliber but may work for other close calibers. It was designed for my printer so you may adjust the slicer if yours prints smaller or larger. The hole on the side is...

Is Your Lee Turret Press Not Auto Indexing Properly Anymore? Your Square Ratchet is Probably Worn Out. It's Simply a Piece of Plastic, So I Modeled and Printed a Replacement in About Ten Minutes. You'll Want to Use a Plastic That Bonds Layers Very...

Upgrading your AA HS Hulls will result in a superior final crimp, and you can find detailed instructions in the accompanying readme file. ...For further guidance, watch this informative video: https://www.youtube.com/watch?v=8H-yO1Z3z5E

The popular Lee Precision Benchplate is used to hold a Lee press to a workbench. The plate is held in place with a clamping system that locks with four 1/4" screws. These knob screws provide quick loosen and tighten with no tools and no lost screws.

This customized version of http://www.thingiverse.com/thing:260104 was created using the Customizer app found at http://www.thingiverse.com/apps/customizer/run?thing_id=260104. You can use this item with these settings: The diameter has been set to...

Created these peg board clips to vertically store the clear plastic case tube for the LEE APP (ammunition processing press)  These clips will fit a standard 1 inch spaced peg board. ... The STL files are for the Prusa Mini.

Made to replace a faulty ejector pin, this upgrade is significantly more reliable and won't ever warp or shatter. ...Find it available for purchase at http://demetersworkshop.com/products/Lee-Pro-1000-Reloader-XL-Case-Ejector-Mod.html.

These are adapters for Small cases (9mm, 223) etc for the Hornady LNL case feeder to the Lee APP press. You'll also need some clear tubing 1/2" inner diameter. ...I used some duct tape to make it friction fit.

The Thing ============ I created a little thing, which will make it easier to size similar bullets on a Lee App, like I do with 38. spec and .45 ACP, without changing the tube holder or adjust the height. This small adatper allows you to keep the...

Customized version of https://www.thingiverse.com/thing:4236659 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4236659