led strip holder 3d models

                                               ...

                                               ...

I printed them at 20mm (4 hours or so,) but they look even better at 15mm.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

The tray should now slide into place.Installing Drawers/Trays under each other• This is the same process as above but instead of mounting the "Rail Lock" into the nut on the rail you will need to slide a “Rail Lock Upper” into place on the back of...

Short pieces of 2020 with nylon foam spacers are used to thermally isolate the bed from printed magnet holders. Pictured is a render of the linear constraint version, along with the final printed versions of all three. My design also incorporates...

Axle parts: Housing 5mm Bearing holder Housing backing Frame parts: Frame parts are able to rotate to fit together. There is the ability to add 2mm steel rods through out where they join. Length range 40mm to 100mm. 40mm are the holes that line up...

And I didn't like the program that came with laser ...How I soldered and assembled the digital ruler, you can look at the video: If you liked this thing - let me know by putting like!Parts links below: Arduino PRO Mini OLED Display Module 128X64 I2C...

Tested in onward. This is a rifle/controller holder I created to play various shooter games on my quest 1 & quest 2. This is a remix from another version that had closed handles. For quicker movement, I opted to cut the controller handle's sides...

Filamet spoolholder X2The filament spool holder X2 for Prusa MK3 can hold any 1kg standard spool (also the 2kg Prusament PLA Recycled) as well as with the 2 different extensions spools up to 4kg or a maximum spool diameter of 350mm. The optional...

repeat that with the velcro cable holder on the other side. For the box, assuming you are using the waterproof version, use the box held flush against the back of the handle so it isn't obstructing the roller to locate and mark the 3 holes for the...

I am including a pen holder that fits the bamboo pens you can find on Amazon or a China site. You could also use a drill chuck or a lathe chuck and create your own mounting bracket to the motor. There is also a modification to my self-centering...

TL;DR first: Welcome to my Overhaul of the Creality Ender 2! Im starting here with version V2 (V1 is only in one picture; there was too much wrong with that), which comes in 2 iterations/stages: ++++++++ Stage 1: ++++++++ changing out the Heatbed to...

Headlight + handle req: ABS filament to print holder, 2 flashlights, 2 Samsung 18650 batteries, 2 M4 screw + nut (15mm long approx.), flexible orange band for handle. I don’t think it’s a big deal, but it would be if the flashlight was any closer. I...

It is a remix of the original spoolholder that uses printed roller arms and springs to press the spool down.To improve the stability of the arm, the profile was divided into two halves, the lower one containing the bushing and separated by a gap of...

I also created a thermometer holder that is designed for the Acurite Humidity Monitor available at Home Depot. This will allow you to monitor the internal temperature and humidity level of the enclosure as needed, and will also allow you to...

I used (4) 3mm heat inserted knurled nuts into the holes at the top of the 2 side plates (Ai3M X Axis CarriageLeft and Ai3M X Axis CarriageRight). Insert the (2) X rod lenear bearings into the Ai3M X Carriage. Screw the CarriageLeft and Carriage...

a clamp to add some tension to the bearing, or a holder for eyepieces or other accessories.MakingCut the aluminium tubes to size. The four legs need to be cut fairly accurately, there is some room for play but not much; try to get at least within...

It fits my battery holder very nicely, and I drilled two small holes to run the wires down into the body (hence the small notch in one side). I did a layer change at the top so that I could print the "exhaust pipes" in silver. I found them here:...

Print profile is in the attached 3MF file and Gcodes, which are for a CR-10 upgraded with a BTT SKR Mini E3 V1.3 with MicroSwiss DD extruder and dual Z stepper using Klipper. Build instructionsSwitch off and unplug your printer just to be...

The Tray: (Optional) Print the desiccant pack holder, “Drybox Desiccant Tray.stl” (Recommended line width, 0.5mm). You could also skip the tray and just add desiccant packs to the empty basin at the bottom of the base too. If adding loose desiccant...

There weren't enough space in the original Hercules carriage for a dial indicator holder so I decided to make this separate carriage for a dial indicator.The Hercules carriage is very easy to remove. Just unscrew the parts cooling fan duct from below...

Use (2) heat inserted knurled nuts at the back of the Carriage top and mount the Carriage PCB holder into these knurled nuts. Slide the X linear rods into the linear bearings now mounted to the Carriage assembly. Install all the original parts into...

Use (2) heat inserted knurled nuts at the back of the Carriage top and mount the Carriage PCB holder into these knurled nuts. 10. Slide the X linear rods into the linear bearings now mounted to the Carriage assembly. 11. Install all the...

...Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work.Our puzzles are modeled using the open-source puzzlecad library.

I Recommend Hex Head screws for the enclosure and drywall screws for the hanging spool holders. 2x or more Ikea LACK tables. (I used 4 for extra storage)<br/> 2x 3M screws 15 mm long<br/> 2x 3M nuts (to replace the PSU with a printed brace)<br/> ...

...Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work.Our puzzles are modeled using the open-source puzzlecad library.

The spindle holder is designed for a 52mm diameter Chinese mini lathe (cheaply available at hardware stores and tool shops). Both nema 17 and nema 23 motors can be used. As a control I use an Arduino uno with its CNC shield and 4 Pololu drivers....

If you're using the stock everything on the X axis, you can orient the Y carriage plate as it was previously.Using the new M5 bolts, mount the belt holder to the bottom of the carriage plate. Pay attention to the belt alignment, which loops to the...

 * **There is no defined end-stop mount on this design yet** Unfortunately, with all the different belt holders, bearing setups and hotends people use on the A8, I can't really come up with an endstop system that...

The content published herein are presumed adaptations of the original copyright holder and are provided to the public under Section 107 of the Copyright Act. Anyone who believes these assumptions are incorrect and material represented herein is...