leatherman micra holster 3d models

Just got my first gun and one of the competition types we have in Sweden called "fält" we are using holsters. Draging the gun up and down with the ordinary chamber flags are a bit hard sometimes, it catches on things. So i made my own and its in...

By request from my Tiny Toy Blaster Mini Holster, I have designed a holder for the magazines used in the Tiny Toy Blaster. Three variations holding one, two or three magazines at any time and a MOLLE compatible clip for attaching it to a vest or...

I managed to mix up the fantastic Yugioh Deck Holster Box by djnicolosi3148 and the Glue gun stand - mini glue gun by Lee-R to create a hot glue gun caddy. A cable wrap is also added around the rear of this project. The stand is a separate part that...

I was having trouble getting a Decal I liked to fit perfectly on my Nuka Cola Blaster, but that all changed when I accidentally damaged it while trying out a holster. At that point, I knew exactly how to repair it on the reprint! I carefully cut...

Horse (https://www.thingiverse.com/thing:4148027) laspistol (https://cults3d.com/en/3d-model/game/valtarian-weapon-arsenal) plasma pistol (https://www.thingiverse.com/thing:4944891) plasma revolver (https://www.thingiverse.com/thing:5372419) hunting...

Anyway, I designed it with 2 countersunk screws (4mm shaft, 8mm head - assuming standard screws fit), a gap to press buttons without removing it from the holster, and high walls that keep it in place, even when equipment is running nearby. I hope...

Under desk tactical holster for CRKT SPEW. Hide it under your desk for rapid deployment. Or mount it underneath your chair, also for rapid deployment. Or maybe like inside a wall, so you could like punch the wall and pull out a little knife. I made...

This stand features a 3/4" copper pipe insert to protect the holster from being melted by the hot end. The hot end doesn't touch the holster, so it isn't absolutely necessary. I've only used this a half dozen times since designing this hangar...

... shorter version that I use with a tandemkross holster. You will still need to cut away or dremel the holster but this way it won't hit the part that attaches to your belt. 0.15-0.2 layer height 100% infill no supports no raft no brim. ...

Optionally there is a picatinny rail and a holster which can be attached to the belt via a tek lok. The tek lok must be purchased from a retailer (pease read the holster assembly). The pistol is powered by theraband gold rubber. The magazine is...

:) Credits: MESH PARTS - straps on belt by AtlantiB (taken from Doppel's Survivor) - holsters from Next Gen Legend by Navid - leg straps and straps on holsters modified by me - belt buckle by Matty-Croft (modified by me) - pants by Sharon_14 - top by...

This versatile configuration is engineered to fit seamlessly into a belt holster, making it an ideal choice for law enforcement professionals on the go. As we await the release of larger configurations, this holstered beauty will serve as a great...

... pushing the floorplate. For even more concealment check out my extended holster wing standoff: https://www.thingiverse.com/thing:4738166 The shape of the front part is subject to change as it does not fully match the profile of the frontstrap.

The highly anticipated communicator from Star Trek Beyond is set to arrive soon, along with its accompanying holster. Update: On April 11, 2020, missing logo files were added to ensure seamless printing and assembly of this intricate model. ... Live...

This means I can queue my spontaneous prints and have some form of order. I mark the enclosure door with the SD card contents (Lack marker holder here https://www.prusaprinters.org/prints/32754-lack-table-dry-wipe-marker-holder) When a print is...

This Picatinny rail attaches to the rear of the TiPX, leaving the main part of the marker clear for use with holsters. The rail is sized for a min reflex sight. It is not large enough for a standard-sized reflex sight, but due to the single screw...

The result is a taller and stiffer belt which I hope will be suitable for supporting a holster. ...Belt height is 38mm (1½"), a sturdy size widely supported by holsters which still fits the belt loops of most pants.Setup for BeltThis setup is suitable...

Included in the files are a piece that can be used to make a holster for the comscanner (for cosplay purposes), and a wall-mountable display bracket (designed for use with 3M Command strips). Parts list for a full build: * Small sheet of 2.4mm...

The holster must be printed with TPU, so that it will conform to the shape of the Buds case. The fit is nice and tight, and the only way to get the Buds out is to push up through the hole on the bottom. The first version has an integrated belt...

Created a cut on battery holster for easier access to screws for momentary switch. Updated 3/22: As per request, I have uploaded base with support for a 12mm switch. I have over-sized it by 0.4 mm making the hole 12.4mm allowing any 12mm switch to...

It's no wonder this firearm is commonly found in the holsters of corpos at the high end of the food chain. Its small size makes it a convenient fit in a briefcase or inside the company limo's glove compartment. And when the situation gets hot, the...

All models can be printed with the following settings: PLA 0.3mm layer height 40% infill Raft recommended for the iPhone_Holster and Tension_Clamp No supports required (yay!) All models should be in the correct orientation for printing when you...

I used PETG at 100% infill for the final part, but lower infill PLA parts were used in the first draft and didn't have any issues with the lighter antennas. Attaches to Peovi cage with the same screws as were included for the protective side rails...

Unfortunately, I'm not particularly fond of the 2D Phillips head driver that comes with my Leatherman Squirt and my Gerber Dime. Since I have a bunch of mini-bit drivers on hand (the 4.5mm size), I decided to create and share a compact keychain...

Printed at .35mm layer height with variable layer height feature enabled in PrusaSlicer on both prints (hence the "racing stripes" on the hook) - the nozzle holster took right under 2 hours and the hook took a little over 5 hours. ...I used 4 outer...

After seeing the Lucky 13 articulated figure by soozafone I knew the amount of articulation could be used for a lot of variations, and this was one of the ones I immediately started working on.I replicated the head and split it into a two piece part...

- I tried to separate che "big block" in my version 2.0 but then the bottom screw would start to rotate if you put too much force while drawing the gun making the holster tilt. So i re-joined the two parts. I've left some space for some washers...

This 3D model includes a police officer wearing the standard attire and equipped with commonly found police gear including: A gun holster to carry a pistol An radio device that provides two way communication A baton or night stick, which law...

To assemble, first attach the holster to the swing-arm plug using a bolt and a wingnut, placing them so that the tab on the plug mates with the cutout on the holster. Then, slip the two retention clips through the notch in the swing-arm plug such...

The picture also shows four battery mounts found on Thingiverse [here](https://www.thingiverse.com/thing:3354548) and one of my other designs, a holster for a Brother P-Touch H100 handheld printer, which can now also be found on Printables...