lcd 5 3d models

This is my 3D model of a "5 inch LCD B Rev2.1 Touch Resistive Screen HDMI Interface 800 * 480 Supports Various Systems Win10 for Raspberry pi3B+/3B/2 B/B+/A" device. The primary purpose of this model is to enable the design of custom cases...

This is a perfect-fit frame designed to fit seamlessly over the Waveshare 5 inch LCD B Display.\r\n\r\nIts sleek design expertly conceals all metal parts and circuit board, with only a precision-cutout to showcase the display and touchscreen. ...To...

It includes a 5" DSI touch lcd which is available at https://a.aliexpress.com/_dWXYgTu and a Raspberry Pi3 - all models which are found at https://www.raspberrypi.org/products/raspberry-pi-3-model-b/. This product fits the Ender 3 And 3 Pro. It...

This is a remix of the case from Thingiverse, specifically designed for use on a Mendel Max 1.5 that has been upgraded to a new controller on its upper right corner. It provides better grip on SD cards for easier removal than my previous model. ... Note...

Remix of case from http://www.thingiverse.com/thing:358878 customized to fit Mendel Max 1.5 on the upper right side. This modification provides a firmer grip on the SD card for easy removal, compared to my previous version. You may need to trim the...

Remix from ....

TFT shield for UNO with SD card

blind plate for the E compartment if you use a RPI with klipperscreen

Based off the great work by Holex01, I've updated his design in the following ways: Added an optional LCD cover (see instructions below) Inverted the direction of the M3 screw to allow tightening at an angle (this also required a slight tweak to the...

Expanded the tolerances of the Y piece, catering to slightly less-than-optimal printers Installing the LCD Cover: Before installing the LCD into the main case, push the Hinge Connector from inside the Main case into the designated slot. The LCD will...

I couldn't find exactly what I needed but Tharmar's amoled screen cover was pretty close - just had to rejig the holes for the various ports (which are laid out differently on the LCD version of this display). Seems to work pretty well, but i'm no...

Case and Stand for SHARP 5.5" 1080x1920 LCD Unit. SHARP 5.5" 1080x1920 LCD Unit. SHARP 5.5-Inch High Resolution CG Silicon Liquid Crystal Panel Set 1080x1920 http://akizukidenshi.com/catalog/g/gM-11967/ Design Data (Autodesk 123D Design)...

My main reason for changing was that the original LCD does not support marlin "Advanced_Pause_Options" which stops you 2 color printing on ender 5 plus with the cura "Change Filament" option. In the pictured example I printed this on Ender 3 Pro...

Raspberry Pi 3.5 TFT LCD touch screen holder is mounted into 2x 5.25 drive bay. USB cable could be wired to 10 pin USB port on motherboard or to back USB port. Holder was designed for Zalman Z5 case, but it should fit to any computer drive bay...

Raspberry Pi 3.5 TFT LCD touch screen holder is mounted into 2x 5.25 drive bay. USB cable could be wired to 10 pin USB port on motherboard or to back USB port. Holder was designed for Zalman Z5 case, but it should fit to any computer drive bay...

This is a housing for the Mini 12864 LCD display to fit inside the Ender 5 Plus chassis without modifications.It bolts on from inside using the original mounting points and screws.You mount the LCD to the back cover first with the M4 screws and nuts,...

This is a housing for the Mini 12864 LCD display to fit inside the Ender 5 Plus chassis without modifications. It bolts on from inside using the original mounting points and screws. You mount the LCD to the back cover first with the M4 screws and...

This is a housing for the Mini 12864 LCD display to fit inside the Ender 5 Plus chassis without modifications.It bolts on from inside using the original mounting points and screws.You mount the LCD to the back cover first with the M4 screws and nuts,...

Required extended screen cable or vertical cut at front to put cable into a shortest way. ... Support only from buildplate.

This device was designed using Tinkercad software. ...Make any desired modifications online at https://www.tinkercad.com/things/xmP3yFtVXjW

I upgraded this product to be compatible with the Raspberry Pi 3 instead of the Pi 4 as was originally intended.

Remix of Hangtight's screen stand updated with adjustable legs and embedded nyloc washers. Parts list: 2x M3 nyloc nuts (recommended, or use regular M3 nuts if they are all you have) 2x M3x12 bolts (M3x16 should fit as well) Printing...

Loved this design for my thermometers but it was falling down all time. Added an extra support part that made it more stable and removed TEMP mark to reduce print time (and I did not like it). ... Printed in PLA at 0.2 resolution with 15% infill,...

This is my approach of the original geometry, without the upper tray. ...

Inspired by Ender 3 full PCB cover with drawers by Doc_Martin.