layer shift ender 3 3d models

I designed this to stop touching the fan by accident, as on one of the ender 3 hot end fans, there was no cover. ... This was made on onshape, and I am the original creator.

Insert a slide-in lamp into your Ender 3 or CR-10 type 3D rail frame-based printer, allowing it to move freely along the frame's rail to any preferred position.

Support de webcam IP pour Ender 3 compatible avec les webcam ip LSC de chez Action, mais certainement avec beaucoup d'autres marques. ... le plateau qui supporte la webcam fait 60 mm de diamètre

feet that raise the printer. ...they use the rubber feet that come with the ender 3 V2 but thats not required. i made these becouse i upgraded my mainboard fan to a 80x25 fan. ...it bolts into the 40x20 extrusion

I created a holder that will hold a caliper on the backside of the PSU fan on an ender 3. ...the original screw can still be used to mount it in place.

92,5mm x 67mm x 29mm 2X MicroSD slots 2X SD card slots 4X nozzle slots 3X Pen slots 1X Glue slots 1X Marker pen slots 1X lighter slots 1X gap gauge slots and slots for accessories ender 3 pro

I needed to run cables under my printer, so I fashioned some custom holders. ...Initially, I placed circular furniture pads beneath them, resulting in a curved cutout, but fortunately, the original rubber pads designed for the Ender 3 fit snugly.

I like both this part: * https://www.thingiverse.com/thing:4654645 and this part: * https://www.thingiverse.com/thing:2924288 So I mixed them together for my Ender 3.

I reverse engineered the Ender 3 Pro, then I made a bunch of changes to improve it. I've been printing on it for over a month now and am pretty happy so I'm sharing it. ... Enjoy!

Just another precision-engineered clip-on roller guide for the Creality Ender 3, requiring a high-quality 608 bearing. ...Conceived and designed using Fusion 360's advanced software capabilities.

Hey everyone, I made this cover to cover the Ender 3 printer profile, and it fits perfectly without needing to take apart your printer! ...It's 200 by 9 by 4.5 in size.

Small bracket to mount the BMG on a stock Ender 3 printhead. Should fit all printers with the same carriage like CR-10, but im not sure. ...Tested with 4240 motor, but smaller motor is better.

Nozzle Holder Attachment Designed Specifically for the Ender 3 Printer, Strategically Positioned at the Top of the QR Code Marker. ... Approximately Thirty-Four Minutes Required to Complete the Printing Process.

Ender 3 Enclosure Prevents Filament Drip: A Simple Fix Using Existing Screws. The Cover Folds Under Bed, Adjustable Screws Required for Secure Fit. ...Ensure Clear Path Before Printing to Avoid Interference.

... Hello, I built this spool holder for my ender 3, it's really useful! If you always use one kilogram spools, fifty percent infill is sufficient. ... Peace.

Led Bar for Ender 3 Ich hab es mit 100% infill gedruckt. 2x 10cm led Streifen zusammen gelötet und an 12 volt angeschlossen. 2x m4 schrauben zum fixieren am profil. ...(Siehe fotos)

Slides on the front of the Ender 3 Y-axis and is compatible with cameras that use the 1/4 inch tripod mount. ...Make sure to check for clearance of the bed and camera.

Creality Ender 3 Filiment roll holder, fits in original spool holder hole. ... didnt need any support to print ( the thread did need a slight sand and spray with wd40) but tightens up nice

Dual Duct 5015 Ender 3, engage printing mode now. Print object with at least 25 percent infill for maximum structural integrity. ...Apply gentle pressure to ensure proper fit and stability throughout the process.

I got tired of seeing the Creality Ender 3's LCD Screen on at night during very long prints since I live in a studio apartment. ...This was my solution to the issue.

The Ender 3's display shines brightly, making it difficult to ignore when the lights are turned off, so I designed a custom cover to effectively block out the glare.

Ender 3 spool prop designed to hold up the other end of the spool holder as it doesn't screw into the lack table well enough to support the weight

Made a Nozzle organizing case for my Ender-3 nozzle collection. ...I didn't Find one I liked or that actually fit my nozzles so I made my own.

This is a small cover to add some style to your ender 3 printer. Just print it and snap it on, over the QR code. ...looks a little better then the QR code that it comes with.

Get ready to rock with the Ender 3! This no-frills powerhouse uses standard parts, so printing is a breeze. ...Installation is a snap - you'll be up and running in no time.

Ein Werkzeughalter für den Ender 3 V2. ...(Passend für https://www.amazon.de/gp/product/B08B3MMLRP/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 ) Kann auch über Fusion angepasst werden .

Ender 3 piggy bank as my tribute to Creality.As I am from Brazil, I adjusted the side fends to allow a Real coin to put in your piggy bank!!

I'm upgrading my Ender 3 printer with a touch of elegance. ...Printing with the letters laid out face down is just the beginning, as I take my 3D printing skills to the next level.

I designed those feet using Autocad specifically for my Ender 3 printer and found them incredibly simple to print. ... Additionally, this was my very first solo project in the 3D printing realm, which made it an exciting experience.

Designed to Fit Ender 3/pro/V2. Designed using Tinkercad will fit snuggly. ... Dimension's: Arm's 132mm Bar 165mm Compatible with standard LED lights 10mm wide Print 2 Arm's, only need one Bar.