lady dimitrescu naked model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

My model was FDM printed only. Actual code will be available here: https://github.com/Kandzior/NeverHotTeaAgain Charging is done by plugging micro-usb cable to the charger module through hole at the side. When you disconnect the plug, you can cover...

It does not need power to work, it is simply a switch that opens when the sensor tip touches a surface. It is probably NOT suitable for a 3D printer bed leveling system because it could touch the model you are printing. If you added a removable cap...

Designed with the help of acoustic modelling software. Comes with carbon fiber slide, complete with PLA stockings.</p> <p>Also available in large bore version at <a...

I did not integrate this into the grill itself as you might want to swap the location of the pi to either side based on your preference.I appreciate any tips to support my work!Print SettingsPrinter Brand:CrealityPrinter:Ender 3...

The models in these STL files are scaled for a 58cm head circumference. (Refer to photo of T800 for how to measure the size you will need to print) Just scale in your slicer software on XY by 1/58*[your figure]. Do subscribe to my YouTube...

The design uses 12 '10mm x 3mm' (the magnets are actually closer to 9.95mm x 2.67mm).This is a spin-off from my earlier light-pull magnetic door catch: https://www.printables.com/model/209370-magnetic-low-profile-floating-head-quiet-door-catc , but...

UPDATE: 20.04.2022adapterplate (new design) for model C&nbsp;Hello, we would like to introduce you to our stealthburner conversion mod.&nbsp;At this time it works only with the klipper Firmware.&nbsp;The use with “Marlin” is planned later and will be...

 A lot of my models are designed for the 2.49mm walls that equate to 6 print lines with a 0.4mm nozzle.  </p><p>Both the Tool Holders and the main Jig are setup to have a color transition at Z height. ... </p><h3>Donations</h3><p>If you found this print...

We don't use the shell.PrintingPrint all models in their original orientations.The parts should be printed with support. Try tree support as it wastes less plastic and is easier to remove in one go.</p><p>I printed my parts in a black/red color...

It's worth the trouble to get access to a laser cutter to get cut panels.&nbsp;&nbsp;The duct is intended to print at a 45 degree angle - the part model is oriented as it is intended to be printed. The duct part DOES NOT NEED SUPPORT. Your slicer may...

I increased the version numbers to reflect this, but if you already printed them you don't need to reprint because there were no actual changes to the models. - Added drop-in boxes to fill with cut-off 12in bamboo shish-kebab skewers, to allow for...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------...

The lamp stand, lamp shade and the bases of these two parts. The models in the STL files have the correct orientation. All parts are printed <strong>without support</strong> and with a layer height of <strong>0.2 mm.</strong><br/> Use an...

Learn everything about the V-Core 3 on the dedicated project page: v-core.ratrig.com. External links: Buy Kit at Rat Rig Step by step Build Manual Facebook Rat Rig 3D Printer Community Project Page (BOM, Build Guide, Files, Electronics, Firmware)...

WARNING: To make sure you're looking at the latest version of our files and documentation, we strongly recommend that you navigate to the Official Project Page. V-Core 3 The V-Core 3 is a premium DIY kit for a CoreXY 3D Printer with no compromises....

If you're using the motor in the BOM or Qidi stock motors use this: xmax-firmware.gcode If using a 0.9 stepper motor you should prin tthis instead: xmax-firmware-optional-0.9-degree-motor.gcode Just place it on your USB stick and print like you would...

Make sure, shaft diameters on knob and potentiometer are the same (6mm or 6.35mm).Model: OEJIndicator: (L)line, (A)arrow, (NI)no ind.Diameter: (50)0.500", (63)0.625", (75)0.750", (90)0.920"Finish: (1)clear gloss, (2)black gloss, (3)clear matte,...

As this is a rather large model it will take a buildplate of 212mm by 175 mm, so this will not fit on a smaller printer's buildplate, but it will fit fine on an Ender 3 and similar printers. My goal was to create a phone holder you can trust with...

Or rather, it's a scale model of what that house looked like fifteen or twenty years ago. The wrecked version is closer to how it looks now that it's been abandoned for the better part of two decades. The tweakers have had a field day with this...

But if you are not confused by the small size, you can also print them on a 3D printer. To increase the size, you can cut these models into pieces, print them separately and then connect them with glue. Download the files you need one at a time by...

# Reddit Post For anyone who want to try this themselves, I created my own "Cloud Streaming Console" by taking a few components I had, modded the plastic on a Gamesir X2 Pro controller, modeled and 3D printed a basic "shell" with some handles and...

Have a close look at the photos and assembled model (wall_clock_07.stl).PlatesThe bearings are hard to push into place, this is where the bench clamp comes in useful to push them flush into the plates.The front plate needs a 30mm M3 screw to hold the...

○ 3 options available § EyeCuSmile_Ribs_V2_RoundedNose.stl - best visibility § EyeCuSmile_Ribs_V2_TriangleNose.stl § Or various developmental ribs models used in the flat pack face covering kit and Version 1 listing of this design. - COMMON...

If you're using the motor in the BOM or Qidi stock motors use this: xplus-imate-firmware.gcode If using a 0.9 stepper motor you should prin tthis instead: xplus-imate-firmware-optional-0.9-degree-motor.gcode Just place it on your USB stick and print...

The 3D printing process sometimes leaves whiskers or small blobs of plastic which might jam the fully assembled power train unless each stage is run-in until all parts are worn smooth when the whole will operate as designed.&nbsp; &nbsp;Assembly:1)...

The design is a complete rework of my older oscillating fan model.It uses a common 130 size brushed hobby motor and incorporates an 18650 battery in its base for completely portable operation. Compared to the older design, the new version has...

The use of simple metal parts in combination with printed components holds a lot of potential for the future; FreeMenDontAsk is already working on other handgun models. Even outside of gun making, this could be useful for a wide array of printed...

In the end I think the best way is to simply open up the 3D-model of the whole maze and just put obstacles together one by one. Therefore I Added a few different files (STEP, STL, 3D-PDF (<a...