lack table 3d models

I use three 6.4mm by 1.6mm rare earth disc magnets, each one a powerhouse of magnetic force. I began with two, but discovered that adding a third significantly improved the overall pull. You can find these amazing magnets at...

I remixed this to hold the 1.5oz hair spray cans as thats usually what I have on hand.

I crafted a custom filament guide specifically for my 3D printer and I'm happy to share it with you, so go ahead and put it to good use!

<p>Rather than remake the dual spool holder, which is perfectly adequate IMHO, I decided to make a small but sturdy adapter to do the job!</p><p>You'll need to print the larger “upper piece” on its side with the slot for the nut facing upright, lower...

<p>Simple threaded knob. Just insert from the back side and screw on the cap. ...I printed in PETG but PLA should be fine as well.&nbsp;</p><p>.4 nozzle&nbsp;</p><p>.2 layer height&nbsp;</p><p>30% gyroid infill</p>

These straightforward instructions focus on positioning the PTFE at the top edge of the Work Surface if you're utilizing an MMU 2.0 model. ...The PTFE simply slides into place, ensuring the tubes remain organized and untangled behind the printer.

Unable to locate a suitable enclosure foundation, I took matters into my own hands and designed a custom enclosure that doubles as a versatile storage platform at its base.

This modification allows the doors to open all the way, and to be removed easily, allowing better accesses to the inards, it won't change the way the latch works.

I created a custom Cable guide based on JayMake's design, and the results were impressive - it looked fantastic. However, I soon discovered that I only had access to 47mm and 35mm hole saws, so I adapted the original design to suit my 35mm saw...

Drill an 8mm hole, then insert the guide and secure it with a screw tightened firmly from the other side. ... Tried it once and it worked perfectly!

I wanted to make an enclosure that had the electronics in the base. This is a work in progress. I am yet to put it together. Am currently working on it. ...

A compact bracket tailored for securing an 85mm ATX power supply unit in place. Enhanced with an accompanying side bracket to circumvent issues arising from wire loom interference on one corner. ...Available in both left and right variants, suitable for...

I created a custom enclosure specifically for this purpose. The design allows for easy installation of the power supply unit in a vertical position, despite its slightly larger size. ...By strategically placing screw holes on one side, I was able to...

<p>10mm Screw and Nut with a tight Lead-Thru-Hole for 4mm PTFE-Tubes</p>

Guide for Standard PTFE Tube to Route Filament from Lower Enclosure Section to Upper and Printer Area. Before proceeding, it's a good idea to test print a few layers and verify that the PTFE tube flows through them without any issues. If necessary,...

I installed a straightforward 1-inch hole grommet, cleverly routing cables from/to my printer through the tabletop it resides on to maintain a tidy appearance.

I repurposed my setup to accommodate standard 1.5-ounce hair spray cans, which are commonly available and easily accessible.

I'm thrilled with how my first Create/Remix turned out! I must say, I'm a big fan of ulightme's spool holder design: https://www.thingiverse.com/thing:2016985 - it's pure genius! Since I've decided to enclose my A8, the top mount holder won't be an...

This design is a compact press-in-place item. It features concealed mounting screw holes in the base and on the sides, but I didn't need to use the side holes since the printed part fit snugly without any fixing. Printed in PLA without difficulty,...

This is a work in progress and has not yet been tested for fitment. ... It is influenced heavily by the designes of YoramSwiers and Woody1978 but it has been remade from scratch as they were not excactly how I wanted them.

I adore those laser level attachments, but when I first employed them, I blurted out numerous expletives while attempting to bore the holes. ... Creating a second laser level stand and opting for this drill hole fixture proved to be an infinitely more...

The device crafts a 90-degree bracket featuring screw holes. ...Future models are designed for improved adjustability of screw hole spacing.

This is an enclosure designed specifically for the Anycubic i3 Mega printer. Its primary function is to maintain a warm environment around the printer, thereby ensuring that the printing process takes place within a consistently heated space. At...

Monted by screws 3,5X40, 4pcs per one completed holder.

This enclosure is specifically designed to fit around the Anycubic i3 Mega, effectively maintaining a heated environment for optimal printing performance. During active printing operations, the temperature inside this enclosure typically reaches...

This sleeker design cuts back on materials while maintaining superior quality standards. It's made with precision and care, just like its predecessor. Screws: You'll need #8 1'' wood screws to assemble this model. Wheels: To find the perfect wheels...

Original Prusa i3 MK3 enclosure crafted from Ikea Lack tables, reconfigured for Ender 3 printers with a 500mm interior height.

I'm currently constructing a custom enclosure around an IKEA Lack table. To start, I already have two Lack tables that I stacked in my room. After the top one fell off twice, with all its contents spilling everywhere, I designed this little helper...