lack table 3d models

A vinyl holder if you built an IKEA LACK for Prusa mk3s. ...I made a holder so I could get my vinyl cutter on the first table. ...Enjoy

Set my Lack enclosure up one table higher and my Prusa started shaking everything bad... Decided to throw together a quick bracket to attach the legs/tabletop to the wall. I created this with a 1/2" gap between the table and the wall in mind. Made...

Drill guide for installing table leveling legs on the LACK enclosure. This utilizes the feet from Thing https://www.thingiverse.com/thing:1840439. The two components fit snugly together on my i3 printer, requiring no additional adhesives if they...

There also didn't seem to be a lot of angle brackets that I liked or that looked decent.  These brackets attach on the exterior of the table, as to avoid conflicting with the brackets on the inside (aka I couldn't be bothered to model this...

Plexiglass/LACK Back-Low and High Adjusted for 2mm Plexiglass

we needed a space to park and hide our robot-vacuum so i printed these legs to use that cheap ikea lack we hadon the picture is the 120mm version, but 100 and 150 are included in the files as welli printed that in petg with 5 walls and 25% infill...

This uses the feet from Thing https://www.thingiverse.com/thing:1840439 The two pieces were tight enough to snap together on my i3, if not they could be glued together. Print instructionsCategory: 3D Printer Accessories Summary Drill guide for...

I decided to print out some samples, and in addition to the long print times, I calculated that it would be cheaper to purchase another table altogether. If only there were a sleek way to connect the legs together...\r\n\r\nSnocat came to my rescue...

Small pipe for routing wires through a sleek Ikea Lack desk Print Settings Rafting: Disabled Supports: Optional

Ikea Enclosure lack leg extendersThey run between the original feet and the Lack legs, and will mean you need a longer screw. ...I created them due to finding out I needed more space AFTER printing all the other parts, I simply glued them to the other...

The table itself can hold 22 pounds, while my extensions were designed to support up to 20 pounds each. Don't try sitting on it, but you can work with this setup without any issues. To make assembly easier, I created a separate lower extension that...

A simple support to screw my ATX PSU under a Ikea Lack enclosure that I build. ...Designed to use the less material as posible.

I'm creating a straightforward support system to install my ATX power supply unit underneath an Ikea Lack enclosure I've built. ...It's designed to utilize minimal materials to keep it lightweight and unobtrusive.

... with dimensions of 105mm x 105mm. A metal ring with a height of 27mm connects the fan to the tabletop. My Arctic P12 Silent fan measures exactly 25mm, and I need to ensure it fits within the 52mm thickness of my IKEA Lack tabletop when installed.

I wanted to secure my table firmly against the wall, so I printed out two of those inserts to attach it to both the table and the wall securely.

It supports the idea that it's an Ikea product and it goes with the theme of the table.

I secured my BLV Cube firmly to my Lack stack by creating these mounts. Print four copies: 1. The original design 2. Mirrored along the X-axis 3. Mirrored along the Y-axis 4. ...Mirrored along both the X and Y axes The mounts keep the cube...

The enclosure was custom-built to perfectly match the original Prusa "Ikea Lack" housing design. To accommodate the Geeetech A10, parts were carefully extended to ensure a precise fit. The plexiglas plates used in this build measure 3 at 48cm x 44cm...

Holder for an extension cable that screws onto the IKEA LACK. ...Designed for <a href="https://www.alza.cz/oem-kf-fb-03-d6128122.htm.">https://www.alza.cz/oem-kf-fb-03-d6128122.htm.</a></p><p>Extension cord dimensions lenght 53mm, width 39mm, height...

Pay close attention to where "Leg" is located, as that's where the leg will be situated, and where "Table" is located, that's where the table will go. ...It makes more sense when it's a single piece, so make sure you check out the original for clarity.

It supports the idea that it's an Ikea product and it goes with the theme of the table.

Directions for cutting legs off a table and extending: Cut legs off 2nd table nearly in half or any additional length needed to make the legs tall enough to fit your printer inside. 2. Temporarily I used clear packing tape to hold the new leg halves...

<p>This is a simple 1" hole grommet. ...I fed cables to/from my printer through the table it sits on to make things look nicer. Print instructionsCategory: 3D Printer Accessories

I misplaced the dowel pins on my massive coffee table and ended up making new ones by myself. ... The simple design consisted of just a single cylindrical shape, which was effortlessly created using Openscad.

... one each other. ... It was designed for 20 (five on each leg) 4mm x 16 mm (or longer) Spax Screws (e.g. [these screws, link to Amazon.de](https://fckaf.de/DHJ)). Print this connector four times and screw them to the table, they will never fall apart.

I reworked the design to accommodate Rolls underneath the table surface. The hole pattern has been tailored specifically for the IKEA RILL 966.713.00 model. ...I also lengthened the bottom by an additional 12 millimeters to enhance overall structural...

This is a sturdy corner bracket intended for installation on table fronts or sides, engineered with robust magnetic capabilities in mind. ...The magnet specifications can be added at a later stage, thereby allowing users to seamlessly attach magnets to...

... my own hair spray holder, thinking it would be a simple task. ...To hold the device securely, I designed it to clip onto the back of a laptop table leg. Once clipped, it stays firmly in place. ...The hair spray itself measures 1.97 inches in diameter.

I'm designing a custom webcam mount for my Prusa Lack enclosure using the Logitech C920 camera. To do this, I need to completely disassemble the webcam until I can access and remove the silver hinge rails from their stock base. These rails are...

Table leg extensions/retainers for repurposed table casing. Guidelines available at: http://www.instructables.com/id/3d-Printer-Casing-from-Repurposed-Furniture/?ALLSTEPS CAUTION: Before relocating a printer to a heated enclosure, ensure that all...