labists x1 mini 3d models

Stacking controller box beneath a 3D printer (LABISTS/EasyThreed X1).

You will want to read up on the following resources (very good) http://cmsj.net/2021/01/12/ez3dbedmod.html https://marlinfw.org/docs/configuration/configuration.html#movement Make sure your board version is correct one for firmware (warranty void...

This is my current Cura profile for the Labists X1 / Easythreed X1, I found the Start-End Gcode on the internet, so they are not my work. I recommend using the attached stl file to level the bed. ... As the bed is not heated (and there's a little of...

Labists X1 and Easythreed X1 rely on a standard external fan duct utilizing a 25x25 fan, currently at an experimental stage. To accommodate this setup, it may be necessary to adjust screw holes using a small drill bit to achieve the required size.

... weak stock Extruder system. ... More informatiion can be found on my website where I'm turning this very bad 3D Printer into a more decent setup: https://hell-printers.videogamezone.eu/2020/12/02/labists-x1-lo-spingifilo-maledetto/ (WARNING: Italian)

Labists, EasyThreed X1 Multi use Filament Guide Hi this is my first design and first 3D printer I got last week and also using Fusion 360 as a first ever. I also included a hook fitment to tidy up the loose cable. All you need is an elastic tied...

#EasyThreed / Labists Reel holder for 1kg You can use a 1kg filament reel sold on Amazon and print out this object using X1 in 4hours.Read notices below and use based on belows. </div> 　 ### Notice 1 Cura must settings 1. **shell**: wall...

**** If you make it and it works, please click like :) **** My X1 has a loose Y axis belt. I tried to rotate the belt attachment to tighten but that was not enough. So I made this. Since the bed of the X1 is not heated, it can be printed in PLA.

**** If you make it and it works, please click like :) **** My X1 has a loose Y axis belt. I tried to rotate the belt attachment to tighten but that was not enough. So I made this. Since the bed of the X1 is not heated, it can be printed in PLA.

Here's my take on a fan mounting for the X1 printer. It uses a full harness that attaches with screws, rather than being strapped on. It's revolutionised my prints - I finally have the warping sorted* I used this blower fan (but I assume all...

For a moment i had stock'ish Labists X1 running on klipper. That was it's cfg file. Not perfect, but it worked. Don't know who would want to use klipper on stock printer like this but here you are. ... [include fluidd.cfg] [include mainsail.cfg]...

... extra accessories. This is a copy of the original publication in Cults platform: https://cults3d.com/es/modelo-3d/herramientas/base-para-control-easythreed-x1 The author is "Planeta Voxel": https://www.youtube.com/channel/UCMIhbkzRju40jV5TnXWcD7w

This holder is a reworked version of Nerys' original design, adapted for printing on an X1 printer with its size restrictions in mind. To print this holder, you'll need to split it into two separate parts and then assemble them together. A July 19th...

I was initially drawn to the concept of a filament guide, but I found the incomplete ring and the fact that it obscured the drive belt for the Z axis to be major drawbacks. To better meet my requirements, I reworked the design from scratch. ...The...

bed levelling test

# EasyThreed / Labists X1 Reel holder for 1kg You can use a **1kg filament reel** sold on Amazon and print out this object using X1. The reel on the left side of X1. 　 ## Cura must settings - shell: wall line count more over **2** - Infill:...

This is a belt clamp designed to let you use the original y axis belt when you do the Nema 17 mod to your Labists or Easythreed X1 printer. ...the hole in the center is made so it can utilize the hole in the bed support that the original belt clamp was...

Hello this is a stepper motor Fan mounting cover for the Labists X1 and other You can use your existing screws from your old cover The Fan is 40X40X20 side blowing fan 12V I used 20mm x 3M nut and bolts to mount the fan Use at own risk

UPDATED: 17 August 2021 DO NOT PRINT WITH SUPPORT Hello This is a stepper motor cooler for a Labists X1 X Axis, should fit other variants too. Its pretty deep holes so you will need a long star point driver, but you can use the same screws as your...

Note if you use a Labists X1 or other to print, this is a large print volume, I was printing 4 blocks at a time, and I highly recommend your Stepper Drivers have heat sinks, your stepper motors have fans and your stepper motor drivers voltage is...

You can use 1kg reel on left side of X1. ... <br> <br> # Cura must settings - shell: wall line count more over **2** - Infill: check **connect infill line** <br><br>

This is a remix of https://www.thingiverse.com/thing:4277658 which allows to keep the original X1 spool holder. ... You need only one of this and 3 of original thing

The Easythreed X1 printer is mostly known for its sharp price. I wanted to make sure the motors get enough cooling. I attached some cheap heatsinks to the motors (X and Y for now) to help them stay less hot. But then the original motor cover was...

Printing: PLEASE NOTE: Due to the clearance needed by the 1KG spool, I could not print this on the X1. Instead, due to the dimensions, you will need a printer capable of printing at least 150mm height. Feel free to remix this to attempt to fit the...

Printing: PLEASE NOTE: Due to the clearance needed by the 1KG spool, I could not print this on the X1. Instead, due to the dimensions, you will need a printer capable of printing at least 150mm height. Feel free to remix this to attempt to fit the...

Modified so that it's wider, and slides directly onto the top of the printer from the rear. A firm grip holds it firmly in place. ...I had to push mine a bit hard to fit it the first time.\r\n\r\nThe one shown in the photo has a rough finish - some...

Simple ventilation system for fan 5015 installable on Easythreed / Labists X1.\r\n\r\n\r\n\r\n

UPDATED: Changed the Covers breath holes V2 to match other fan cover in my projects Hello this is a fan adaptive plate and cover for Labists X1 and Easythreed I removed the old axis cover and created a new axis cover what fits a fan. You can use...

I made this to see if it would improve the cooling for the Labists SX1 printer I use.

This mini cooler is a custom fit for the TronXY X1, but its design makes it adaptable to other models as well. I've created a specialized NSS adapter that pairs perfectly with the 50 mm radial fan this duct connects to. Check out the adapter here:...