l shaped couch white 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

Screw the tee shaped adapter into the top of the hot end using (3) 3X25mm screws. Then secure the adapter into the effector using (2) 3X30mm screws. I placed a 30mm fan in the back blowing in to a closed fan shroud. I placed a 30mm fan in front, also...

I used the based plate shape. - The motor mount uses @djos_1475's https://www.thingiverse.com/thing:4797901. The center hole has been widen a bit more to make sure that any thick couplers will have clearance. - The top mount / bearing block was...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes shape =...

I’ve also a couple of ports (antenna and micro USB) that I also wanted to exclude the fuzzy effect from around.Since PrusaSlicer allows for any shape of modifier to be used, in CAD I selected the area I wanted to be fuzzy and extruded them two...

If I print 3 wall lines, one string hangs into the gap, but is easy to remove with a small v-shaped knife. You should have a 2nd view on the wheel bearings, they should run soft but I had problems printing a perfect bearing, V16 seems to solve...

This design allows each half to flex sideways, and the conical shape adapts to differing shank diameters. The 22 cell holder is the largest possible size for my printer (and probably the largest practical size as well). I elected to print this size,...

If you have trouble getting the wire through, feed through the white pull wire, strip the end and solder it to the red and black wire. Use that to pull the red and black wire through, then cut off the pull wire.</p><p>Loop the red and black wire back...

These are needed on walls only as mentioned above.Attention: For the “front” part it is important to perform 2 color changes:From 0 to 1.2mm height the color is black or whatever darker color you like to use.From 1.2mm to 2.4mm height the color is...

Optional: Lightly paint letters on cover (white or black would be good choices, as would adding glow-in-the-dark pigment), or use Sharpie marker or paint pen --- # Builds and Remixes I would love to see builds of this project if anyone actually finds...

You'll want the hotend at the bottom with the shortened PTFE tube sticking up into the white filament guide above. Then the large gear above it and the printed short handle on the side.Use the 20 mm M3 bolt, spring and washer to secure the printed...

You'll want the hotend at the bottom with the shortened PTFE tube sticking up into the white filament guide above. Then the large gear above it and the printed short handle on the side.Use the 20 mm M3 bolt, spring and washer to secure the printed...

I found a lot of nice designs online, but almost all of them relayed on you printing models in white and then paining them with the colors you like.&nbsp;I have also designed all parts to have 0.3mm fit offset so that you don't have to use XY Size...

I cutted some dupont female-female black/white pairs by half and created a 5V GND multi-ouput octopus... you will need at least 5 pairs of 5V/GND... those would be for arduino, antenna, Throttle Pot, Steering Pot and a last pair for "top-plate" pots...

You'll want the hotend at the bottom with the shortened PTFE tube sticking up into the white filament guide above. Then the large gear above it and the printed short handle on the side. Use the 20 mm M3 bolt, spring and washer to secure the...

If you have trouble getting the wire through, feed through the white pull wire, strip the end and solder it to the red and black wire. Use that to pull the red and black wire through, then cut off the pull wire.</p><p>Loop the red and black wire back...

Shorter lenses give stronger magnification and longer lenses give weaker magnification.To remove the lens from the tube, looking from the bottom of the tube, use pliers to pull downwards on the head of the 50mm locking screw, which will retract the...

While cooking and working at the restaurant Bob always wears a white apron and the figurine is also portrayed holding one of his incredibly delicious burgers. If the 3D printing figurine could talk, we are pretty sure shocked Bob would be screaming...

Then restart OpenSCAD.4) OpenSCAD won't pick up newly installed fonts in C:/Windows/Fonts.In case new fonts are missing, put the font TTF files also inC:\Program Files/OpenSCAD/fonts/Liberation-2.00.1/ttf and restart OpenSCAD again.&nbsp;The names...

I printed my dual-color prints with a single extruder by pausing the printer after the colored backround part had completed and then swapping in a spool of white filament. My printer doesn't support the M600 pause command so I have to pause it...

If you have trouble getting the wire through, feed through the white pull wire, strip the end and solder it to the red and black wire. Use that to pull the red and black wire through, then cut off the pull wire.</p><p>Loop the red and black wire back...

You'll want the hotend at the bottom with the shortened PTFE tube sticking up into the white filament guide above. Then the large gear above it and the printed short handle on the side. Use the 20 mm M3 bolt, spring and washer to secure the...

I cutted some dupont female-female black/white pairs by half and created a 5V GND multi-ouput octopus... you will need at least 5 pairs of 5V/GND... those would be for arduino, antenna, Throttle Pot, Steering Pot and a last pair for "top-plate" pots...

In the pictures with two benchies, the black one is off of the belt printer whereas the white one is from a CR-6 SE as a comparison point.NoteThis is still a work in progress and you will most definitely find issues. Currently, I've identified a...

If you have trouble getting the wire through, feed through the white pull wire, strip the end and solder it to the red and black wire. Use that to pull the red and black wire through, then cut off the pull wire.</p><p>Loop the red and black wire back...

In the highly detailed figurine, the shape-shifting monster throws himself into battle while his deadly weapon-like tendrils sprout of his body and wreak havoc all around. The remarkable attention to the figurine's anatomy that speaks of dynamism and...

Madam Wilumbra comes on a 60mm BaseYiggral comes on a 105x70mm Oval BaseThe Umbratouched Spritelings come on a 25mm BaseThe Umbratouched Grovestalkers come on a 32mm BaseThe Hexgrove Cauldron is without a base, as it functions more as a terrain...

this can be used to have the separator walls not reach the top of the wall 1-4 Bottom Magnets can now be added to each compartment. 2018-12-14 Version 4.3 improved the shape of the support cylinder for the lid magnets to better blend into the...

If you'll notice, it has seemingly impossible shapes with lots of spheres and overhangs, but my Little Replicator That Could handled it all with aplomb. You might be surprised to find that my project has inspired you to design more adventurously. ...