kywoo tycoon 3d models

226 3d models found related to kywoo tycoon.
Kywoo Tycoon Max Undertray
Kywoo Tycoon Max Undertray
thingiverse

This was designed to alleviate the stress on the wiring harness leading to the heating bed of the Kywoo Tycoon - Max. The wires travel with the X movement and can get snagged on the the aluminium extrusions at the base of the machine. ...In some cases...

Kywoo Tycoon Y-switch
Kywoo Tycoon Y-switch
thingiverse

On my new Kywoo Tycoon the position of the Y-end-switch was not correct. I was not able to reach y=240. So it moved it 5 mm to the right. ... I made two variants - for M3 and M4 hex-nuts - for M3 and M4 threaded inserts for melting

kywoo tycoon bed handle
kywoo tycoon bed handle
thingiverse

I realized there isn't really a bed handle for the kywoo tycoon printer and I didn't want to keep contaminating the glass bed with my finger prints so I made a snap on handle. The back of the handle is curved so that you can grip onto it with your...

Kywoo Tycoon Drawer
Kywoo Tycoon Drawer
thingiverse

This is a drawer for the Kywoo Tycoon to store the tools and utilities. I have designed two kinds of housing, one full, easy to print, and one with hex-structure to save filament. But then your machine has to be good adjusted, out of the box there...

Supports rails linéaires KYWOO TYCOON
Supports rails linéaires KYWOO TYCOON
thingiverse

Salut, voici ma version améliorée des supports de rails linéaires pour les imprimantes KYWOO TYCOON et TYCOON MAX. Plus solide et plus facile à régler que la version d'origine. ... Allez voir la vidéo pour plus de détails.

Hinge for Kywoo Tycoon Cover
Hinge for Kywoo Tycoon Cover
thingiverse

This is a hinge for the Kywoo Tycoon Cover. I didn't know, what to do with the cover, when I wanted to do anything inside the building room. Put it on the floor, carry it to a table nearby or anywhere,. So I created this hinge to simple fold it up,...

Kywoo Tycoon Wiring Clamp
Kywoo Tycoon Wiring Clamp
thingiverse

Wiring harness clamp for the Kywoo3D Tycoon 3D printer. Installs between the filament runout switch and the bracket that holds the runout switch. Uses the existing screws as it installs over (around) the stand-off posts for the switch. NOTE: This...

30mm-40mm fan adapter Kywoo Tycoon
30mm-40mm fan adapter Kywoo Tycoon
thingiverse

30-40 mm fan adapter for Kywoo Tycoon printer

Kywoo Tycoon End stop switch board mount.
Kywoo Tycoon End stop switch board mount.
thingiverse

Y axis end stop board/switch mount for Kywoo Tycoon.

Spacer for Z-AXIS Kywoo Tycoon IDEX
Spacer for Z-AXIS Kywoo Tycoon IDEX
thingiverse

These is Spacer for Z-AXIS Kywoo Tycoon IDEX. ...(2 pillars)

Kywoo Tycoon Slim 3D Printer Screen Cover
Kywoo Tycoon Slim 3D Printer Screen Cover
thingiverse

Kywoo Tycoon Slim 3D Printer Screen Cover, to protect the LCD ribbon from damage. ...Model created by one of Kywoo's customers, MS Tong.

Kywoo Tycoon Slim 3D Printer Fan Duct
Kywoo Tycoon Slim 3D Printer Fan Duct
thingiverse

Kywoo Tycoon Slim Fan Duct. It can also apply to Tycoon/Tycoon Max, and can be used with the DIY extruder cover(thing: https://www.thingiverse.com/thing:5144461). ...You also need to remove the hotend cooling fan and install it above the fan duct, as...

Kywoo Tycoon Vertical Mainboard Mount
Kywoo Tycoon Vertical Mainboard Mount
thingiverse

The Tycoon by Kywoo is a pretty good printer that is held back by a blackbox of a mainboard and OEM only Marlin flavors. Well, this is --Sparta-- 3D Printing so nuts to that. This design allows for mounting an SKR Mini E3 v3 and Raspberry Pi to the...

Kywoo Tycoon TL smoother holder
Kywoo Tycoon TL smoother holder
prusaprinters

This is a pair of clips that fit a type of TL smoother and the clips will fit the Kywoo 2020 frame.  It could also be used for other 2020 frames.  The clips have an offset so that when installing inside the box it does not protube outside.I printed...

Kywoo Tycoon TL smoother holder
Kywoo Tycoon TL smoother holder
prusaprinters

This is a pair of clips that fit a type of TL smoother and the clips will fit the Kywoo 2020 frame.  It could also be used for other 2020 frames.  The clips have an offset so that when installing inside the box it does not protube outside.I printed...

Kywoo Tycoon Filament Holder
Kywoo Tycoon Filament Holder
thingiverse

Mounts off the original screw holes, but does require 2 longer screws. Requires two 608zz bearings and two longer screws. 54mm and 52mm spool adapters included (print two of them), or just place smaller spools on the axle. The washers go towards...

Kywoo Tycoon Fan 5015
Kywoo Tycoon Fan 5015
thingiverse

Bigger air outlets, fits well in the original fan position(3 screws), gives more airflow and improves layer cooling, printed in PETG or ASA for better heat resistance, needs SUPPORTS only on the base, hope you use it and tell me your experience.

Kywoo Tycoon Fan 5015
Kywoo Tycoon Fan 5015
thingiverse

I have not tried it, I have done it based on suppositions and the piece that you have published, so I do not know if the placement that I have given to the 5015 is the correct one when a Home of X is done, if someone wants to try it that he does it...

Kywoo Tycoon Tycoon Max DIY Extruder Cover
Kywoo Tycoon Tycoon Max DIY Extruder Cover
thingiverse

This DIY extruder cover suits Tycoon and Tycoon Max 3D printer, can't fit in Tycoon IDEX and Tycoon Slim. It also can be used with Tycoon Slim fan duct, (Thing: https://www.thingiverse.com/thing:5144500). You need to remove the hotend cooling fan...

Kywoo Tycoon Y-Axis endstop bracket and hotbed support
Kywoo Tycoon Y-Axis endstop bracket and hotbed support
thingiverse

This is a modification to the Y stop mount and the front right hotbed mount for the kywoo tycoon. ...

Kywoo Tycoon Slim Z-Top Cover
Kywoo Tycoon Slim Z-Top Cover
thingiverse

Simple Tycoon Slim Z-Top Cover

Kywoo Tycoon Y Limit Switch Mount
Kywoo Tycoon Y Limit Switch Mount
thingiverse

The original on my tycoon max broke, so I made a replacement based off the original, but with slots for m4 nuts to reduce stress. I also included a version like the original that require threading the bolts through the plastic if you don't have spare...

Kywoo Tycoon cooling shroud with 4020 fan
Kywoo Tycoon cooling shroud with 4020 fan
thingiverse

The original cooling set up for the Tycoon is insufficient with its one 4010 fan placed under the extruder. I found that other set ups existed with 5015 but it seemed complicated and none used the existing attachment. I designed the shroud to use...

Kywoo Tycoon IDEX 3D Printer Waste Filament Collecting Box
Kywoo Tycoon IDEX 3D Printer Waste Filament Collecting Box
thingiverse

This box can collect waste filament from the Kywoo Tycoon IDEX extruder. No screws or tools are needed to install. ...Users can print two boxes and simply place them under the nozzle brush, then they will help keep your printer and the print clean and...

Kywoo Tycoon Slim 3D printer Lead Screw Bearing Assembly Unit
Kywoo Tycoon Slim 3D printer Lead Screw Bearing Assembly Unit
thingiverse

To use this unit, you need to print one "Kywoo Tycoon Slim 3D printer Screw Bearing Base" and one "Kywoo Tycoon Slim 3D printer Screw Bearing Base_Mirror Version", two "Plastic base insert". ... There are also some other accessories that you need to...

Kywoo Tycoon Fan Duct - Angled
Kywoo Tycoon Fan Duct - Angled
thingiverse

I slightly modified the original by continuing the 45 degree downward flow of air to be aimed more at the tip of the nozzle as opposed to horizontally straight into the heat block. I'm sure they'll have a better design in future iterations. ... Print...

Kywoo Tycoon Bed Alignment Corners
Kywoo Tycoon Bed Alignment Corners
prusaprinters

Print in materials with high temperature resistance like PETG for best durability.Model should be oriented flat side down and if possible printed at 100% infill to minimize any deformation when heated.

Kywoo Tycoon Slim TF Card Slot Auxiliary Tool
Kywoo Tycoon Slim TF Card Slot Auxiliary Tool
thingiverse

Sometimes when the TF card is inserted into the Tycoon Slim, the card will be accidentally dropped into the machine. ...This model can better prevent the TF card from being inserted in the wrong place.

Kywoo Tycoon IDEX Fan Duct 5015
Kywoo Tycoon IDEX Fan Duct 5015
thingiverse

Fits Tycooon IDEX extruder without black metal shroud. It´s possible it works with the shroud but i can´t test it anymore. This model is for the left extruder but can be just mirrored to fit the right one with bl touch. It uses only 3 out of 4...

kywoo tycoon 5015 rhd fan duct
kywoo tycoon 5015 rhd fan duct
thingiverse

the base fan duct was taken from the EVA carriage design for the RHD fan duct (https://main.eva-3d.page/addons/fan-ducts/) inspiration came from this design with a long duct and fan mounted at the rear: https://www.thingiverse.com/thing:4916779 ...