kuromi drawing 3d models

(Added instructions for the wires on the lower legs) Added Explosion drawing and parts list for reference [Update 10.1.2020] I published the files for the light modification and the stim thrower I mentioned below, you can find them here:...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Forums suggest power draw inconsistencies. EDIT (18/12/2021) - OK, you can possibly ignore the statement above. Yes, you do need a a decent power supply, and yes, there are known issues with the JMicron chipset, but I managed it once without issue...

Unless it can be lubricated with a special Teflon grease, which does not have an aggressive effect on plastic, but for this operation there is access through the slot.Installation diagram of support bushings:I also want to draw your attention to the...

But it also lets the fan draw air from above, rather than from right off the bed with the fan's 45 degree angle (ala PRUSA MK3). This should provide better cooling, and also avoid problems that some MK3 users have had with fan motors making noise...

https://youtu.be/23A9o62kssQ I'm not going to draw a sketch for the electronics. I'll just list the wiring below. There's not much clearance in the case for wiring, so be neat. :D Pin 12 -> switch -> ground Pin 3 -> stepper IN1 Pin 4 -> stepper IN2...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

...like how long I can spend drawing designs or documenting them. E-Gor can't help with that. But checking how well the Roomba is cleaning, looking for the cat toys (of which there are many), recovering crashed drones (<100mm) - he can and does for me.

Even so, the Carrey drawings show the representations on many of the missing sections and have enabled us to locate a number of existing fragments. The original length of the frieze along the south side was 58.70 m. It was composed of forty-seven...

I ensured there were no gaps around the part cooling exhaust ring.So I went back to the drawing board and designed this new compact mount. There are three versions, 35mm stock fan, 40mm, and 50mm hotend cooling fans. It is smaller, more compact, and...

One way to get a close measurement is to use a pen and mark the existing bumper by drawing a line using the edge of the toilet rim as the guide. This will give you an approximate position for the clip on the main bumper. Keep in mind that if the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

Likewise, if all the cards are in the active deck (whether draw, discard, or in play), then you would only have a red cube. If some of each, then there is a red cube on the inside representing the count of active cards, and a green cube further...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

For the drill pattern, see the technical drawing. You can probably use a 1.5mm or 2mm plate as well, 1.7mm was just what I had around. In fact, you can use any thickness you want, the only thing it influences is the alignment of the drag chain mount...

TO DO Just the drawing for the dark red LED filter window. It's just an obround with two indents where the pins are, they are melted over to hold the filter. NOTE: this takes a while to render in OpenSCAD as $fn is set to 170, but drop it to 25 for a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Your support has given me the motivation to keep this project going. As the first year draws near, I decided to update and combine both stl into one project and include a new version of AFS2 that is beefier… I call it AFS2_FulTank. More info below...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

Tooling files are stored in Zip K40_Bed_Thermal_protect.zip.NOMENCLATUREEngine support :7 x CHC DIN 912 M3x30 screw1 x M3 Hex Nut2 x 608RS ball bearings2 x M8x20 spacers (aluminum profile see plan)1 x GT2 gear 20 teeth M51 x K40_Bed_Motor.stl1 x...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...