korg volca knobs 3d models

Slip-on Knob for Korg SQ-1 and Volca Series Designed with Dimensions Inspired by Davies 1900H Series - 15.5mm Height, 12mm Diameter, 6.4mm Inner Diameter The top of this knob is hollow, allowing the LED on the SQ-1 pots to be visible. This design...

Slip-on knob for Korg SQ-1 and Volca series available, boasting 15.5mm height, 9.6mm outer diameter, and 6.4mm inner diameter. The top is hollow, allowing a clear view of the LED on SQ-1 pots. This slip-on knob fits perfectly when printed in TPU,...

Press fit POT upgrades for the Korg Volca series. They fit over the narrow stock POTs, not replace the existing knobs of the unit. ...Print in clear or semitransparent material to allow the light to show through.

This is a press fit knob upgrade to give more control to the small POTs on the Korg Volca series. This is not to replace any knobs, but to press fit these over the top of the slim POTs. ...Print in clear or semitransparent material to allow the light to...

Stand for korg volca keys. ...Just mirror other part for set stp model for edit is attached Enjoy!

The Korg Volca Transport Box is a compact case designed to store the Volca series of synthesizers. To assemble this box, you'll need two neodymium magnets, specifically cylindrical in shape with dimensions 10x5 mm, and some screws for assembly. ...A...

Angled Stand for Korg VolcaThis is a simple one-piece design that attaches to any Korg Volca to raise and angle it. ...It works well when placed behind a small desktop keyboard, like the Korg microKEY or the Korg nano controllers.

Stand for Korg Volca all models, by simple clipping. ...You just need to add 4 small non-slip pads in the areas provided for this purpose on the bottom.

Self-contained stand for assembling two Korg Volcas of any model, by simple clipping. ...You just need to add 4 small anti-slip pads in the areas provided for this purpose on the bottom.

Use one of these as a stand to elevate your Korg Volca boxes for improved visibility and functionality. ...They can be oriented at two distinct angles, providing versatility in setup.

This is a compact base for Korg Volca, designed to be printed in four separate components. ...Two supports and two pedestals make up the structure, held together solely by tension until assembly is complete.

This is a 40HP Eurorack panel designed specifically for mounting Korg Volca synthesizers directly into your Eurorack system. To integrate the Volca, remove its case from the PCB, desolder battery and speaker cables, then use four original screws to...

# Volca Case Transport case and dust protector for all Korg Volca synthesizers made with OpenSCAD The design can be customized Please visit the github page for details sources and newest releases ## How to build one Feed the template to a lasercutter...

Remix of the Korg Volca stand by beejums.This simplified and slimmer version is enough to hold your Volca securely.Print 2 models and enjoy making music with a better viewing angle on your Volca ;-) 3D Printing settings...

The human stands tall as a flagship for the renowned Volca series of electronic instruments crafted by Korg. ...Its sleek design commands attention, occupying a noticeable amount of space, yet exudes an aura of sophistication and style that is sure to...

Stand for a Korg Volca. Designed to stand just above a desktop synth without blocking any of the rear ports. Prints on the "back" as shown in the model and last photo. No support needed. ... More info at...

Inspired by a Korg Volca Stand found on Thingiverse, I came up with my own unique design for two Volca units. While it may not be as sleek as the original, this stand gets the job done perfectly. Make sure to print one left piece (marked "L") and...

An enclosure for Jason Hotchkiss's awesome passive mixer, somewhat matching the Korg Volca dimensions and look. You can change the number of channels (and lid thickness etc) in the top of the scad file. The STL contains 4 channels. My build uses an...

A simple fix for not working KORG Volca synth (any) rubber buttons. There're many cheap conductive glues on the market, but the problem is after drying they become too rigid and easily fall off the flexible silicone. The idea of this fix is to...

An enclosure tailored specifically for Jason Hotchkiss's impressive passive mixer is now available, mirroring the Korg Volca dimensions and sleek design perfectly. The top section of the scad file can be easily modified to alter the number of...

It rests on the plastic edge so it would protect the knobs in a backpack or similar snug mean of transportation. It should fit any volca. It's a bit of a loose fit (0.5mm on each side, so 1mm clearance). I could reduce it to .5mm but I'm not...

... on both side of the Volca sequencers. Holes are on the outside of the mount so build your rack with this in mind. If you want the screws on the inside of the Volca sequencer use: https://cults3d.com/en/3d-model/various/korg-volca-wood-mount-1

Do you have a Korg Volca and need a dust cover to keep those precious knobs from getting crunchy? The Volcover is for you! ... -Printed at 0.2mm layer height, takes about 9 hrs on a Creality CR-10s -No support necessary -Printing the first few...

ENGLISH:Stand with modular elements to better organize your Korg Volca synths.There is an additional module for the Volca Modular cables that fits into the base that supports the synth.If you also own a Korg NTS-1 you can add it to the stand by...

I built this holder to clear up some space on my desk and showcase my Korg Volcas mounted neatly on the wall or pegboard. It fits snugly, ensuring they don't wobble when I play them. Update: The initial design had slightly too long arms. I forgot...

This rail mount allows you to mount many Korg Volca sequencing devices into a standard 2040 V-Slot Linear aluminum extrusion rail. I used 16mm 5M hex head bolts with T nuts to secure the mount to the 2040 rail. Two mounts are needed on both side of...

This is a stand for the Korg Volca series mini-synthesizers. It has some cut-away area that I use to help with cable management that also saves print time. I printed two for stability. ...I am also attaching non-slip stickers cut from these: ...

I'm a bit short on surface space, so I decided to mount my three Volcas above the shelf where my Korg Monologue synth is currently sitting. It's standard Rubbermaid "Twin Track" shelving - the kind you often find in closets. I designed and 3D...

Remix of the Korg Volca stand by beejums. This version of the stand will hold 2 Korg Volcas. Additional supports/parts are not required to keep the Korg Volca's in place. Print 2 and slide onto each side of the devices. Originally printed using MG...

Wanted a dust cover for my Korg Volcas, ended up with this ingenious thing that lets me store them easily as a stack. There's no need to remove the shroud if I'm using them - it's actually quite convenient to leave them on as a hand rest and it also...