korg electribe 2 knobs 3d models
893868 3d models found related to korg electribe 2 knobs.
thingiverse
These attach on top of the stock knob that came with my Makerbot Replicator 2. The internal hole allows for easy installation at the end, preventing a tight press fit from the top of the bore, and only the last 2.5mm is pressed in. The bottom of the...
prusaprinters
ENGLISH:Stand with modular elements to better organize your Korg Volca synths.There is an additional module for the Volca Modular cables that fits into the base that supports the synth.If you also own a Korg NTS-1 you can add it to the stand by...
thingiverse
This is a press fit knob upgrade to give more control to the small POTs on the Korg Volca series. This is not to replace any knobs, but to press fit these over the top of the slim POTs. ...Print in clear or semitransparent material to allow the light to...
thingiverse
Korg Kaoss DJ Decksaver 2 * KKDJ_3A 2 * KKDJ_3B 2 * KKDJ_3C 2 * KKDJ_3D 1 * KKDJ_3Mid_Top 1 * KKDJ_3Mid_Bot 1 * Schraube M5 1 * Mutter M5 I've revised the side panels C and D once again, as the initial version was a bit too precise and fit too...
thingiverse
Simple holder for a KORG guitar tuner that hangs on the guitar stand.
thingiverse
This is a replacement for lost battery lid of KORG AX5G guitar effects processor
thingiverse
Angled Stand for Korg VolcaThis is a simple one-piece design that attaches to any Korg Volca to raise and angle it. ...It works well when placed behind a small desktop keyboard, like the Korg microKEY or the Korg nano controllers.
thingiverse
Created with Customizer! ... Instructions Using the following options: Top_Radius = 1.5 Thickness = 0.8 Depth = 22 Hole_Size = 5.25 Gap_Width = 0.25 Lock_Type = "Multiple Notches" Slot_Width = 4 Cross_Tie_Spacing = 5.6
thingiverse
... fall off the flexible silicone. The idea of this fix is to provide flat stiff surface for the glue. 1) Print it 2) Sand the bottom surface 3) Paste some conductive glue (i.e as shown) 4) Place inside original button 5) Assemble and use. ...
thingiverse
Stand for the Korg SQ-64 sequencer. ...This model is one end so you need to print two of them.
thingiverse
Stand for korg volca keys. ...Just mirror other part for set stp model for edit is attached Enjoy!
grabcad
The 61-key Korg Karma keyboard is designed specifically for electronic music studios, serving as a model in layout planning.
thingiverse
... of the logo to STL format and then extruded the background, then the letters from the background. This was made for a vintage Korg synth restoration where an original badge was missing, but it's also just a cool little item for fans of Korg stuff.
prusaprinters
Remix of the Korg Volca stand by beejums.This simplified and slimmer version is enough to hold your Volca securely.Print 2 models and enjoy making music with a better viewing angle on your Volca ;-) 3D Printing settings...
thingiverse
... right piece (marked "R"), then secure everything together using four rubber bands. Alternatively, you can use the holes to tie it all in place with a small cord. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Supports: No Infill: 30%
thingiverse
11mm wide and roughly 11mm tall replacement knob made specifically for the Korg Triton Extreme Workstation synthesizer/keyboard. ...(May work on other keyboard/synthesizers if the peg the knob inserts into measures roughly 4.5mm thick at the base.
thingiverse
Korg 05RW Support for Vise Settings - Print Settings - Printer: Dagoma Discoeasy 200 - Rafts: Not Available - Supports: Yes - Resolution: 0.20mm - Infill: 1.75
thingiverse
A sleek little case for the Korg Monotron Delay that prints out in approximately four hours, given a resolution of 70 mms.
grabcad
The Korg Kaos Pad is an innovative MIDI controller designed specifically for electronic music studios, facilitating efficient and creative layout planning.
thingiverse
This is a stand for a Korg SQ-1 sequencer. I made it tall so it can stand behind other gear. ...Printed with white Inland PLA+, wood base.