kobra elite gunstock 3d models

Simple feet extensions to raise the Kobra Max up about 1 inch. This then allows for a little more easy air flow for the electronics. I used the large pucks for the four corners and the small ones for the two front center legs. ...Using them this way...

Replacement fan duct for Anycubic Kobra. Original fan duct is kind of fragile, so I've broken mine while disassembling print head. I designed a new one as much as close to the original with slight improvements for better printing without supports. ...

Remix to fit my Anycubic Kobra. On the right side you can see 4 holes, they are for box with some addition electronic (step down module to reduce extruder fan noise and to supply extruder light. I will post this project lately). ...

This remix of the baseplate adding rail slides as @Stewey1954 did in his design of the Anycubic Kobra Max Tool HolderThese slide straight on and do not require any screws etc. ...I printed them on their side so I would not require any supports.

This is a remix of another project modified to be able to fit an Anycubic Kobra. The screw hole was also adjusted to be able to accept a 1/4 inch screw. ... I printed it on it's side and it required no supports.

Wanted some Elite warbands for S&H, so I slapped these together.

Elite class Warbot with turret mini cannon and dual saber gutter blades.

To attach it, you first have to remove the plastic cover with the 'Anycubic Kobra' emblem on it. The mount then simply slides on the metal piece. Usually, the mount should be tight enough to hold on its own, but you can insert a 2x2mm piece in...

Replacement feet for the Anycubic Kobra Go or Neo. They increase the base feet height by 8mm. The OEM feet for the Kobra Go were 20 mm so these are 28 mm. Use the screws from the old feet to install these. I added a stainless steel washer beneath...

... <p>Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=948783 Instructions Using the following options: FrontFaceText = Anycubic TopFaceText = Kobra BottomFaceText = 3D Printer Tolerance = .5 Category: Office

Kobra Neo/Go Light Bar that snaps into the underside of the top frame rail. I used 12V LED strips so I wired a 12V zener diode in series with the positive wire. You can also use a 12V regulator or alternatively use 24V LED strips to avoid the...

Da der Anycubic Kobra Max in ein Gehäuse gebaut wurde, mussten eine Umlenkung des Filaments gebaut werden. Hierzu werden lediglich folgende Teile benötigt:1x Kugellager 60031x M5x20 Senkkopfschraube1x M5 Mutter2x M3x25 Schraube2x M3 MutterSince the...

A quick & dirty way of sitting a camera with a lrgerbase on the side of the Kobra Neo. Measurements are taken to allow the front part to slip nicely over the frame on the right hand side & the plate is set far enough back to stop the printhead...

I currently use his design for my Vyper and decided I liked it so much that I decided to remix it to be compatible with my Anycubic Kobra Max. Currently, every piece is complete with the exception of the widened platform chain mount. ... This part is...

Based on MaraMagus' Nerf to Picatinny Rail Adapter (https://www.thingiverse.com/thing:992285) and the Russian military's Kobra red dot sight, with as much detail as I could get in Tinkercad. ...There is a slot down the frame - this allows transparent...

The latest version now features an Elite size of 41FR, ensuring a comfortable and stylish fit for its users.

This is a cutting-edge surface model of the top-rated gaming mouse: The Razer DeathAdder Elite.

Tool tray for the Anycubic Kobra. Holds all the tools that came with the printer. Slides into the front left rail. The rail end cap can be taken off to expose the rails. A test print for the rail fitment has been included to check your...

Tired of toasting my fingers, I made a bed handle for the Anycubic Kobra. The left and right feature embossed cobra snakes. (I will upload one without the snakes too when I can) The fit is pretty exact so you might need to do a tiny bit of sanding on...

I was looking for a mount to attach to the front of the Anycubix Kobra Max printer to hold a trakphone with Octa4a but couldn't find any so I made this one up. I used 3 parts from https://www.thingiverse.com/thing:3543845/files,...

This is a filament guide for the Anycubic Kobra (not Kobra Max). I'm pretty sure this won't help or hurt your prints, its more of an organizational thing. When I started using a bearing aided filament spool holder, the filament would come out in...

Modified the original design to accommodate the Anycubic Kobra.There are two files, one you print three of, the other you print one of. </strong>The file you print one of is for the back left corner where there are a few screws and plates that...

I figured I needed a filament guide, and didn't like the options I found out there for the Kobra.This guide has a print-in-place ball that is sized to fit a small piece of teflon tube. It mounts to the small 3mm hole that is already in the OEM Kobra...

The original design is great, I didn't change anything except for the fitament for the Kobra because it lifts the printer about 29mm while also providing absorption for vibrations that can cause ghosting in prints. I printed them out of PLA at a...

UPDATE 07.08.2023 added two new parts (not tested yet!): endcap_duo_simplifiedx70mm (for “holder+20mm”) endcap_duo_simplifiedx90mm (for “holder”) these allow the spoolbracket to be mounted on the anycubic kobra plus aswell. See therefor: ...

Here's Your Customized Block Puzzle - The Elite Mexican Created with the Customizer App at Thingiverse Congratulations! You have customized your very own block puzzle. To build it, follow these easy steps: Building Your Elite Mexican Puzzle Using the...

Tired of toasting my fingers, I made a bed handle for the Anycubic Kobra. The left and right feature embossed cobra snakes. (I will upload one without the snakes too when I can) The fit is pretty exact so you might need to do a tiny bit of sanding on...

With the Kobra being so new, i had not seen anything really made up for it, and I wanted a Z mounted camera for timlapses. This design fits around the belt tension section, and is made to be held in place with 2 M3 screws, length isn't a huge deal,...

This is a ring light for the Anycubic Kobra. I purchased the Led Strip from Wish.com I cut the led strip to the length that I needed, then ran the cable to a plug I used clear UV resin to attach the strip to the plastic ring back, then I used...

Adjusts the height/offset of the Inductive Probe used on AnyCubic Kobra Neo.This will set your Y offset from 4 to 0.In the larger holes a M2.5 Heatset Insert is used, original mounting hardware for the adapter plate to the OEM probe mount.This will...