klipper config for anycubic predator by 3d models

People are taller for allowing a two-kilogram load. ...Designed for fifty-centimeter centerholes. ... Manufactured in PETG, using minimal bed supports.

... ... Some small adjustment to the microswitch arm may be necessary. What you need: Two M2x20 and two M2 nuts to assemble the case. Two M3x12 and two M3 washers for mounting it on backside of the threaded holes for the original sensor. ...

... drive motor in a stable and reliable manner. ...To prevent any potential damage, this mounting point should be situated near one of the Z-axis risers, allowing for an adequate clearance between the effector and the Z-pillars, even when fully extended.

My Printer klipper config for Creality CR10 V2. You have to mount your cable to the z-endstop AND 3d-touch. notice that linear / pressure advance is not possible for stock cr10v2 creality mainboard with klipper. ...(tmc2208 in stealthchop) have fun

This is a slicer config file for the Anycubic Slicer (tested on 1.3) that will work on any Kobra 2 model. You may have more configurable options but the main settings in this file will help almost everyone. Added Gcode before and after print help...

Small Orbiter V2.0 Flying-Extruder-Mount for Anycubic Predator

... PRO on fluidd .. ...with 3dtouch probe Cura Startcode: START_PRINT BED_TEMP={material_bed_temperature_layer_0} EXTRUDER_TEMP={material_print_temperature_layer_0} Cura Endcode END_PRINT Link for Klippersceen https://www.thingiverse.com/thing:5415704

Note, the linked code requires the rpi's uart gpios so for your connection between the printer board and the pi for klipper, use the rpi's USB not uart gpio like I explained above. To avoid a USB cable, I soldered to data pins on the underside of the...

Note, the linked code requires the rpi's uart gpios so for your connection between the printer board and the pi for klipper, use the rpi's USB not uart gpio like I explained above. ...To avoid a USB cable, I soldered to data pins on the underside of the...

Update of Ultimate Anycubic Predator Effector (V6 & 4010 fans) for Haydn Magballs ;) Enjoy

https://www.printables.com/social/402878-account/models COMPANION PART: https://www.thingiverse.com/thing:5722475 This is useful only if you are running Klipper, and have an ADXL345 Accelerometer (or a pair of them, one for the toolhead and one for...

Ultimate Anycubic Predator Effector (V6 & 4010 fans) for Haydn Magballs. ... Thanx to Superbeasti for the wonderfull effector design <3

anycubic predator Printbed

This is useful only if you are running Klipper, and have an ADXL345 Accelerometer (or a pair of them, one for the toolhead and one for the bed). I don't know if this will fit any others. I made the part I jammed on to this bed handle a while ago,...

I neded a holder for all the tools of my 3D printers (Anycubic predator, photon zero). So I designed one in Fusion360. ... Feel free to use.

Needed a mount for both the PI and the Fan for a klipper upgrade for the AnyCubic PredatorYou will need 4 m3 heatset inserts to mount the board to the mount

I discovered that the spool holder on my Anycubic Predator Delta printer had become quite noisy, so I took matters into my own hands by creating a custom pad to reduce friction and provide a silky-smooth surface for the filament spool to rest...

Anycubic Predator Carriage Adapter for Haydn Magball Arms (Remix) ==================================================== Description ------------- I take an existing carriage adapter designed by Haydn Huntley, originally intended for the Anycubic...

Changes Implemented: * Swapped out the mount to accommodate a non-standard LCD screen, replacing the stock LCD of the Anycubic Predator * Created additional space for integration with the PanelDue board * Upgraded the ribbon cable to 10 ways,...

This is a clip connecting Mosaic Palette 2 to Anycubic Predator. ... 02.02.20 - uploaded a complete setup, get it here: https://www.thingiverse.com/thing:4140259

### Credits - [Anycubic i3 Mega X carriage and Hemera mod](https://www.thingiverse.com/thing:4238185) by Sergiu-I - [BLTouch support](https://www.thingiverse.com/thing:4167435) by OmNomNomagon - ["Filler" filament spool...

Do not use this, I had to recalibrate my Anycubic Predator and then the original from https://www.thingiverse.com/thing:4441076 is perfect for the Turmberg3D - Hotend Set , bigger hole for the heatsink is nessisary...

Designed specifically for Anycubic Predator Rods, it can also be adapted for printers with similar rods. Unlike a Rod Damper, which applies lateral forces, this system relies on the inherent resistance of flat cable ties to counteract twisting...

... Read's posts on Facebook: facebook.com/groups/2134289353555625/permalink/2248853505432542 and facebook.com/groups/2134289353555625/permalink/2248853118765914. The translucent yellow parts were printed on a Photon by Tai Hromnak for his Predator.

This is a spacer for the underside of the predator effector for the probe magnet.

This video demonstrates how to connect the Mosaic Palette 2 to the Anycubic Predator. ... 02.02.20 - A full setup is now available, check it out at https://www.thingiverse.com/thing:4140259

This is a Display cover for the ANycubic Predator, no supports required it will fit perfect,without any screws

Here is a video John Giardino shot: https://youtu.be/jtPPRN12znc These parts were inspired by some of Rizza81's designs: https://www.thingiverse.com/thing:3567642 They were also inspired by some parts which a person named Flint Read posted on...

MGN12 adapter for the Anycubic Predator, rails are mounted directly on the extrusion without any adapters. I have been printing with these carriage for a few weeks already at 150mm/s outside wall; 200mm/s inside wall and infill with no issues. ...

Extruder and filament sensor mount for the stock extruder and filament sensor of the Anycubic Predator. Normally the Predator has a "flying extruder", which means the extruder is mounted with springs to the three carriages. Problem of this: Extra...