klackender 3d models

## KlackEnder Probe KlackEnder Probe - **Simple, fast and cheap!** Adaptation of the [Klicky](https://github.com/jlas1/Klicky-Probe)/[Quickdraw] https://github.com/Annex-Engineering/Quickdraw_Probe) Probe for the Ender 3 and comparable Creality...

Here's a mount for the KlackEnder probe Rev 2 by kevinakasamhttps://github.com/kevinakasam/KlackEnder-ProbePrint with supports and pretty strong (many perimeters and high infill).Options provided for MK8 style or V6 style hotends.For the V6 (What I'm...

Looks like the hot end mounting plate changed on the Ender Pro. ... One hole was moved 1mm to the right and the x rail extrusion hit the bevel of the original design so I removed some material.

This is a remix of the probe dock to include an extension on the front side. I was having the probe fling forward occasionally when docking. With this extension have not had any issues with docking since. ...(well over 50 docks at this point)

very quick hack to adapt Kevin akaSam's Klackender design to my linear rail stealthburner. this is remixed from another stealthburner X carriage block to add the probe mount there. Basically some mounting positions has to be offset to...

The KlackEnder config works for the basics though. I used it to get setup, then moved to the more in depth setup. Theres is a lot of extra movements in this video, but I have since worked out a few of them. It doesn't dock between homing and meshing...

<p>Looks like the hot end mounting plate changed on the Ender Pro. ...One hole was moved 1mm to the right and the x rail extrusion hit the bevel of the original design so I removed some material.</p>

These are Klackender parts modified to fit an Ender 3 V2 Neo with Sprite Extruder Pro. Changes made in Tinkecad because I'm lazy. Retainer and dock modified to fit newer 4020 rail V-slot and bracket and set back 11mm for increased X-axis maximum. Had...

Arm to attach to the shaft of nema 17 motor to move sexbolt endstop out over the ender 3 bed for automatic z offset calibration using KlackEnder mod.

Based of fandabrabec design. ... Had magnets left over from my KlackEnder project and figured id put them to use instead of buying the rectangular magnets. ...Enjoy.

... a V6 hotend (non-volcano) with the Frank2.0 ecosystem. ...Only tested using the linear rail mount. Mounts for the sherpa mini and orbiter 2 are included.Klackender should not be affected. ...Not tested

Modified to fit the stock Clockwork 2 files, spaced out to fit the HartK Stealthburner toolhead board, BL-Touch mount has been removed, and a groove has been added to the rear for the https://github.com/kevinakasam/KlackEnder-Probe&nbsp;Note,...

I was heavily inspired by the KlackEnder by KevinAkaSam (https://github.com/kevinakasam/KlackEnder-Probe). My printer has linear rails which prevented the KlackEnder from working with my setup. Also, I was unable to get consistent results with...

It adds a high-mounted EBB42 and CANBUS umbilical as well as compatibility with KevinAKASam's KlackEnder klicky probe. The belt and Klack mount can be found here. Edit: I realised that the Klack mount was a little too short, so I extended it by about...

Instead of adding more fans on the printer head where it adds weight and make it sometimes ugly huge to be effective, this puts the blower on the side of the X axis beam and so it isn't putting any more weight on bad places while still adding much...

I haven't mounted a bed leveling probe yet, but I'm looking at trying the Klackender probe: https://github.com/kevinakasam/KlackEnder-Probe Drop a comment with any questions or issues, and I'll do my best to help or adjust the design. ... I did this at...