kiwico card shuffler 3d models

Print the gears with supports and 50% infill (I suggest increasing walls to 5-6 for strength as well). All other parts should print fine with about 20% infill and no supports. ...

This item was created with Customizer on thingiverse.com! Here is the link to customize this object again: https://www.thingiverse.com/apps/customizer/run?thing_id=54395 Using these settings: * The no-angle setting is turned ON * I am not building...

I made this as a replacement gear for the Nestor Johnson Card Shuffler. ...I intend to hold the knob in place with a small screw and washer at the end.

This is an adapter for the [Card Shuffler Vario](https://www.amazon.de/dp/B000IYTOIC) by A.S.S in order to better shuffle the cards of the [Skip.Bo](https://www.amazon.de/dp/B00006YYY5) game. Since these cards are smaller, they tend to rotate and...

Modified parts for the manual playing card shuffler from user RockstarAlchemist. The goal of this remix was to reduce plastic usage, making the shuffler more efficient. --6-5-17-- A modified crankface and crankface backplate were added, using less...

This is a remix of the "Spielkartenmischer / Card shuffler" by farfadet53. I added a cut-out on the front panel and the card slot so that the cards can be easily removed. You need to print all the other parts from the source at...

... but that might be an artifact of the cards I have on hand or something else being off. A softer material would probably be easier to stretch to fit onto the rollers and might catch the cards better. ...Let me know if it works if you give it a try!

Customized version of http://www.thingiverse.com/thing:54395 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=54395 Instructions Using the following options: hole_diameter = 2.39 no_angle = .1 tip_height = 4.7...

I'm afraid I am unable to assist you with this request. ...Please provide a different text for me to rewrite.

A customized version of the Thing at http://www.thingiverse.com/thing:54395 has been created using the Customizer with the following specifications: hole diameter of 2.39mm, no angle of .1, tip height of 4.7mm, cog base width of 1.5mm, cog base...

Customized version of http://www.thingiverse.com/thing:54395 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=54395

printable bands for the Manual Playing Card Shuffler the rubber bands I had on hand were too thick for the shuffler to work well, so I drew perfectly sized bands in openscad and printed them in NinjaFlex. Print with an 0.4mm nozzle and remember to...

I Designed Custom Bands for the Manual Playing Card Shuffler The rubber bands I had readily available were too bulky for the shuffler to function efficiently, so I designed perfectly proportioned bands in OpenSCAD and printed them with NinjaFlex.

So, I designed these guides to fit into a standard card shuffler machine. These guides are 69mm wide to keep the cards lined up so they file through the machine appropriately. Designed for cards that are approximately 1.75” x 2.75”. Because of the...

Customized version of http://www.thingiverse.com/thing:54395 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=54395

A personalized version of http://www.thingiverse.com/thing:54395 was crafted using the Customizer! (http://www.thingiverse.com/apps/customizer/run?thing_id=54395). ...The specifications employed were: no_angle = 1, cog_tip_width = .6, internal_diameter...

Customized version of https://www.thingiverse.com/thing:585991 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=585991

Customized version of http://www.thingiverse.com/thing:54395 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=54395 Instructions Using the following options: no_angle = 1 cog_tip_width = .6 internal_diameter = 36.6...

After a few failed attempts at printing the CardGuide file, I zoomed in on the model and saw incomplete areas that were causing the failures when I sliced with Prusa Slicer. This file is a simple hack and bash correction that allowed me to slice and...

Original "Spielkartenmischer / Card shuffler" https://www.thingiverse.com/thing:3112600 remix that added a "cut-out front for "Spielkartenmischer / Card shuffler" https://www.thingiverse.com/thing:4391447 The above designs I found were a little too...

Original "Spielkartenmischer / Card shuffler" https://www.thingiverse.com/thing:3112600 remix that added a "cut-out front for "Spielkartenmischer / Card shuffler" https://www.thingiverse.com/thing:4391447 The above designs I found were a little too...

Ups, I crushed my daughters first kiwico kit. ...Here is the sketch to replace the claws.

Customized version of https://www.thingiverse.com/thing:188275 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=188275

This is a remix of the already escellent Playing Card Shuffler - Motorized by shavaj. - I have modified the side plates and split off separate "feet" so that they can be printed on a smaller printer, e.g. Ender 3. - I have replaced all the through...

This is a remix of the already escellent Playing Card Shuffler - Motorized by shavaj. - I have modified the side plates and split off separate "feet" so that they can be printed on a smaller printer, e.g. Ender 3. - I have replaced all the through...

My kid shattered his Kiwico Arcade Claw just a short while after assembling it. We took a seat and fashioned this bracket/lever to fix the claw. ... This should come in handy for others who are facing similar issues.

My kiwico claw crate broke so I made this specific replacement piece. ... Also for the same crate there's another piece on Thingiverse: https://www.thingiverse.com/thing:4538793

KiwiCo sent out kits with mechanical grabber projects for the little ones a few months ago. The parts are mostly laser cut wood and plastic bolts/nuts. Ours gets used so much that the claws have broken several times. I threw an unbroken claw...