kite string spool 3d models

Printable kite string spool Designed to be printed with support everywhere. 10% in a concentric pattern works well and is easy to remove. ... Holds at least 500ft of light kite string

3D printable spoolIntended to be printed with support everywhere. ...10% in a concentric pattern works well and is easy to remove.

This is intended to be printed in two parts and then glued together. ... The spool is fairly large and not intended for small kites with thin line. ... Pictured on the spool is 500ft of 200lb line.

Reel for flying line or kite. ... Video of printing and assembly: https://www.tiktok.com/@betta3d/video/7142512365723143430

This is a compact kite string winder designed to alleviate the monotony of rewinding kite string onto the small spool holders typically included with kids' kites. A version 1.1 upgrade has been implemented to reinforce the sides, which were prone to...

Attach the kite string to it, then easily switch the clip between kites. I suggest printing this in ABS at 100% infill with no supports needed. You might need to lightly sand it to fit your kite's string hole perfectly. Note: This model hasn't been...

Should help reduce the tedium of winding the kite string back on the small string holders that come with children's kites. I added a version 1.1 to stiffen up the sides. After I wound up the string with some good kite tension on the line the sides...

Should help reduce the tedium of winding the kite string back on the small string holders that come with children's kites. I added a version 1.1 to stiffen up the sides. After I wound up the string with some good kite tension on the line the sides...

You can tie the kite string to this and then switch the clip between kites easily. I highly recommend printing in ABS at 100% infill to get the best results. No supports are needed, but you may need to do some sanding to fit your kite's string hole...

This is another “string winder” to wind and manage the line for flying a kite. Most designs I have seen were too small for my taste. That is why I made my own design. ...

I'm Looking for a Kite String Reel That Prints Without Supports Needed The handle is a nice bonus, making it easier to reel in the string, but I can only fit one or two fingers inside. My kids, on the other hand, can easily get most of their fingers...

This is another “string winder” to wind and manage the line for flying a kite.Most designs I have seen were too small for my taste. That is why I made my own design.</p><p><a href="https://www.buymeacoffee.com/AoO2SOds2Q">Of course you are completely...

Enhance your kite-flying experience by using this tool to wind strings more efficiently compared to the standard ones that accompany inexpensive store-bought kites. ...To utilize it, simply print its STL file and slot the spool's handles into place.

This thing lets you wind the string for you kite better than the flat ones that come with the dollar store kites.

This innovative design allows for easy storage of kite strings and saves time. It's the first item I've made specifically for 3D printing on my upcoming Robo3D Printer. Feedback is appreciated as more spin stick outs will be designed and tested...

Assemble one 150mm and one 200mm ring-type kite line spool using acrylic or wood parts cut from our provided file design. Firstly, remove any unwanted materials from the pieces. Next, lay one ring on a flat surface, inserting the internal remnant...

I was working on a project where I had to employ a drill to simultaneously wrap multiple strings around a spool.

You can use this model if you haven't got that much string left so it keeps everything tidy. I used supports for these ones but I haven't tried without them.I used 5% infill for this.

You can use this model if you haven't got that much string left so it keeps everything tidy.&nbsp;I used supports for these ones but I haven't tried without them.I used 5% infill for this.

Get ready to meet Spooly, a game-changing design that lets you wind up your kite spool in just under a minute using a device most people already have at home - an electric drill. Simply plug Spooly's axle into your drill and pull the trigger. A bit...

... took approximately 4 hours per piece. The final result came out significantly stronger than expected. Regarding materials, I could not find my kite string so instead used thin-gauge decorative wire and a twisty-tie to serve the same purpose.

<p>This was just a quick design to help grow my modeling skills.</p>

String Spool Holder ShelfHolds spools of string, wire, tape or whatever with a small shelf above.As seen in the images, this is compatible with, and can be mixed with Small Shelves:https://www.printables.com/model/204736-small-shelvesPLA Pro.2 Layer...

... Mason string. ...It uses 8mm threaded rod, 2 lock nuts, and 2 608 bearings. I printed using ABS, minimal infill (5%). This allows for quick outlay and reeling of long strings of any type. ... I also included the stp version in case you want to modify.

A spool to hold thread for nail art. ...Spool holder is a 6-32 machine screw. ...Print Settings Printer: BorgBot Rafts: Doesn't Matter Supports: Yes Resolution: .3 or lower Infill: 50% Category: Art Tools

Fast and simple spool for a kite.

Since I couldn't find an effective way to secure the string to my head, I created these cord locks myself. To use them, simply insert 1/2-2/3 of a spring from a ballpoint pen and it should provide ample tension to keep your mask firmly in place on...

Spool cap for Worx string trimmers.Should be compatible with various Worx string trimmer models (WG150, WG151,  WG152, WG153, WG154, WG155, WG156, WG157, WG160, WG163, WG165, WG175, WG180, etc.)  Suggested to print in ABS or ASAFusion 360 source &...

This is a caddy to carry a spare spool of trimmer line on a Worx string trimmer.  It should be printed from TPU to allow a spool to be pressed on & removed easily.  Attach to trimmer shaft with either zip tie or velcro strap.I used 2 top/bottom...