keymod attachments 3d models

This makes any maintenance or extruder swapping/tip replacing a simpler job as the whole mount comes away from the carriage (with extruder and coolers still attached), giving excellent access to the extruder without the need for mass dismantling. As...

There are also some for the X rail but they involve a new design for the plywood side panel, which I've attached as a STEP file. This allows the belt to run through the part instead of the awkward 90º turn that's quite hard to clamp properly. You'll...

You can either use the slots to attach a few screws through into the bottom side of the base table or simply use the red double sided foam tape that is super sticky and strong (will usually say 15lb rating). UPDATE 26May2021: Added a remix case...

• Replace the two screws holding the hotend fan in place with (2) M3x18mm socket cap screws to attach the BLTouch mount. • Made sure the BLTouch wires are are sitting flush in the mount and are not touching the fan. • Wires are secured at the...

This board had everything I required for a new Intelligrill; a decent processor, a lithium ion battery port with charger, wifi, analog input, plus the ability to easily attach an oled display. I ordered the Feather Huzza ESP8266 and an oled board,...

No electric drill is needed to operate however if you want to use an electric drill, you can, just pull off the crank arm and attach a 13mm socket to the gear shaft instead. Thank you and Enjoy! As a FYI: I noticed that the original design's gear2...

This component cooler is a remix of: https://www.printables.com/de/model/430339-the-100-the-fastest-3d-printer-based-on-a-printed- see also: https://github.com/MSzturc/the100 I attached the Creality "High Flow Kit" to the cold end, but not with the...

One for the bigger teflon tube holders is attached as well.\r\n\r\n> I also added a version with a hole offset for mounting on the side of the SAMLA where a gap exists - so the two parts of the feeders won't fit together any more. The filament will...

(The chamfer on rear part will accept most 3.5 up to 5mm countersunk wood screws.)Installation:drill holeinsert plug (in to hole)attach paper clamp using wood screw guided through rear hole of rear clamp part. If you choose to pre-assemble...

Attach the Covers. Use X60 Filament as a Gasket, Cut Slightly Long So the Ends Press Together and Seal. Take One of the Drive Gears, Stick It on the Back of the Pump by the Magnets, and See If It Spins (Roughly at First) If Not, You May Have Issues...

There are handles attached to the supports for easy removal. As noted above, due to the curve, this area is not as smooth printed at .2mm as I would have preferred. 5 - Glue the head_spike into the head and then glue that to the body. I tried...

If you do, please link them in the comments for others to see and use! Extra assembly informationThe UFO upper and bottom parts are attached with five UFO plugs. The first time it will be a very tight fit but once the UFO has been opened a...

Toolless accessory mount --- This mount allows you to attach custom addons to your 3D printer with toolless operation for adding additional functionality to your machine, be it vinyl cutting, pen plotting and more. The air duct acts as an...

The Robo 3D attaches the Z-axis limiting switch to the X-axis mounts so that it 'floats' just under the X-axis. When the nozzle touches the build plate, the limit switch is triggered. In this case, an OMRON 5E4 T85...

It is just when the glass plate gets attached things go haywire and the glass plate warps. Could be a bad glass plate? Research shows others have that problem. Change to metal? I haven't had much problem with my prints coming off the glass. I hear a...

The 3A buck converter needs to have the onboard pot desoldered and replaced with wires attached to the B10K pot. Only two leads are required, the third one on the board isn't connected. Make sure you wire it up so that turning the pot clockwise...

However Etsy limits how many files I can attached and total file size so I will have to email them to you upon request after your purchase. I additionally can scale the parts and make parts fit your specific print bed dimensions upon request. There...

The attached photos help additionally! A few tips nevertheless: When gluing the inlays, be very careful. Only very small amounts of superglue should be applied ... a little is more! the rod should be bent a little before insertion so that...

The attached photos help additionally! A few tips nevertheless: when gluing the inlays, be very careful. Only very small amounts of superglue should be applied ... a little is more! the rod should be bent a little before insertion so...

Gerber files are attached. Any comments are welcomed. Here's how I designed this: Motor Driver I selected the ALLEGRO MICROSYSTEMS A4973SB-T chip to drive the motors. This chip has FET driving transistors, so it should have a low voltage drop and...

The Arduino code is located here: https://github.com/cncartist/arduino-project-box The full pin-out tutorial is shown in one of the attached images. You can follow the diagram for wiring, using your best judgment for wire lengths. There is only one...

Nine different tail units can be attached, some in different orientations. I first wanted to do the vertical axis with a ball bearing (it's still possible), then I used an 8 mm round steel bearing with a tip, it works perfectly. The two labyrinth...

UPDATE 24th of May 2019 Released an enhanced final version of the blaster, which can be found here https://www.thingiverse.com/thing:3634012 UPDATE 27th of April 2019 -Made a Stock attachment lug which can be found here...

Also, I use a T-Link TL-WR902AC mini travel router to extend the Wi-Fi range and use Jaewook Chung's mount adapter https://www.thingiverse.com/thing:4621599 to attach the TP-Link router and power supply to the top the ZWO ASIair Pro. That would be...

After printing it's necessary to attach the three screws holding together fan and pulley; one way you do this is by first enlarging each M3 threaded hole in 9 mm of size until an interference fit on the shaft that still remains can't be reached. If...

Next attach the 2x M3 bolts with 1x M3 nut each from the back of the stock through the back plate. At last screw in the 2x M3 bolts through the back onto the front piece. Software The software runs on the ESP8266. The web app is stored in SPIFFS...

Use the small space behind the usb-a port.3) Attach the short alignment tab to the USB module like in the picture and insert it into the base.-All the alignment tabs were designed for a friction fit, but when inserted there is room on the underside...

These could be attached with small screws or glued on. Or break out your favorite 3D modeling program such as Tinkercad and combine the mount tab with the speaker adapter.You can select to make this in either millimeters or inches. If you use inches...

Attach the handle to the sign: Now, take the large remaining piece of foamboard and mark where you want to install the handle. I prefer that the handle reach about half-way across the sign, thus leaving a good amount of handle extending past the...

Attach left and right alignment jigs - If the fit is right, they should 'snap' into place tightly. Now slide the table (which was away from you) /towards/ you, sliding over top of the mounts, as close as you can pull it towards you. Torque the 4...