keyhive sofle 3d models
69 3d models found related to keyhive sofle.myminifactory
After buidling a Keyhive Sofle RGB Kit I realized that I didn't like how the plates were connected. With the default plates the PCB floats in the middle and is really only held in position by the keyswitches. To remidy this I designed a 3d printed...
thingiverse
A custom-made coin features a distinctive emblem bearing the KeyHive logo.
thingiverse
A remix of https://www.thingiverse.com/Erdos "v2 Sofle RGB Tent Case" to use M3 size tenting legs instead of M4 since I had previously built some M3 tenting legs based on the IMK Corne build guide (https://imkulio.com/build-guide.html) I also added...
thingiverse
Based on Sofle Carry Cases by givingco. Resize top cases to be printed on 15x15cm printer. Create holes to easy unfold. ...
thingiverse
This is a fast and simple carry case for a Sofle version 1 ergoboard. It is designed to have ~3mm of eva foam added to pad it but it is not necessary, the fit is still nice. ...The design wont work if you have plates or encoder knobs that extend past...
thingiverse
Simple Sofle V2 (https://josefadamcik.github.io/SofleKeyboard/) case inspired by https://www.thingiverse.com/thing:4720213 When printed in transparent PETG underglow works great, otherwise one could make some holes in the bottom for leds to shine...
prusaprinters
A tray mount case for the Sofle v2 split keyboard. ...Note that this is designed for the actual version 2 of the keyboard, not the RGB version, which is sometimes referred to as v2.1 (and sometimes falsely as v2!) Check Josef's page for more...
prusaprinters
I recently printed effae's Sofle V2 case but wanted a tenting solution. These legs give the case a 21.5 degree angle and have a nice wide base to securely glue them on. They are designed to fit between the screw by the thumb buttons and the inward...
thingiverse
WIP Tenting Case for Sofle Keyboard. The design is to allow for M5 bolts to be screwed in and used to adjust tenting. M2 spacers still required. EDIT: 26 Jan 2021 I was able to print a prototype and have added images The indents for...
thingiverse
This is a custom case for a wireless Sofle RGB split keyboard build. The bottom of the cases have slots for four 20x5mm magnets, which are used to hold the tenting legs and can also be used to attach the keyboards to each other as to make a...
prusaprinters
Remove lower PCB,No heatsets needed: bolts thread right into the case bottom plastic
thingiverse
Plates for the Sofle V2 Keyboard. 3mm thick. ...Happy clacking!
thingiverse
**END EDIT** You will need (4) M2 6+3mm Male-Female Standoffs and (4) M2 4mm Screws For details on wiring and firmware: https://github.com/foureight84/sofle-keyboard-pimoroni My other designs for the Sofle Keyboard: Base:...
prusaprinters
This is a remix of the Sofle V2 RGB Beveled case created by thysdewet on thingiverse:https://www.thingiverse.com/thing:4753682/files It is intended to use M3 Socket Cap screws (3 per side) to attach the mount to the modded Sofle Case. ...It then...
cults3d
High profile case for my sofle v1 keyboard. I wanted something more closed than sandwiched acrylic plate+bottom. There are holes for m2 inserts so the keyboard will stay in place. I'm planning to add rgb underglow so I've changed filament at 34 and...
thingiverse
... the underside of the PCB). My other designs for the Sofle Keyboard: Base: https://www.thingiverse.com/thing:4755855 Pimoroni Trackball Mount: https://www.thingiverse.com/thing:4756591 MCU and OLED Housing: https://www.thingiverse.com/thing:4784085
thingiverse
#**This doesn't work for v1 or v2 Non-RGB PCB's** **I included the STEP files in case someone wants to make modifications in their modeling software.** Tenting case for **Sofle v2 RGB** split keyboard. The **bottom layer** can be **laser-cut...
thingiverse
... that this case is built around can be found here: https://josefadamcik.github.io/SofleKeyboard/build_guide_rgb.html There's a few variants of the keyboard, e.g. from Keyhive, that are floating around, so I hope this doesn't confuse anyone.
thingiverse
Plates for mounting the Sofle RGB keyboard PCB to. ...Original repo which designs were downloaded from: https://github.com/josefadamcik/SofleKeyboard
thingiverse
Changes - increased height - added cutout - tenting holes with 7mm diameter for heat set inserts This is compatible with sofle keyboard v2.0. This is not compatible with v2.1. ...
prusaprinters
... wanted to experiment with tenting angles without going crazy on disassembling and making a case. ...This just snaps on to the thumb side between the PCB layers of the keyhive kit. The result gives a fairly sturdy 15 degree tilt. ... Category: Computer
thingiverse
I wanted to experiment with tenting angles without going crazy on disassembling and making a case. ...This just snaps on to the thumb side between the PCB layers of the keyhive kit. ...The result gives a fairly sturdy 15 degree tilt.
thingiverse
Used the svg provided by josefadamcik in his [github repo](https://github.com/josefadamcik/SofleKeyboard/tree/master/Sofle_v2/Case). Plate thickness and lip dimensions can be customized in the provided FreeCad model. Variables are inside the...
thingiverse
This is a quick and dirty remix of [foureight84](https://www.thingiverse.com/foureight84/designs)'s pimoroni trackball mount that lengthens it enough to fit the Sofle v2.1 top plate. If you have a v1 or v2, you can find the og stl...
prusaprinters
It’s great for using the board on a desk pad or if you put it in a bag.The ultra-thin version of the case has recesses that fit the sockets, diodes and solder joints, allowing the Sofle to sit even lower. The difference is about 1.8mm in theory, but...
thingiverse
... Crkb travel case by taksi_kavausuki (https://www.printables.com/de/model/117598-travel-crkbd-magnetic-case). I took the idea to include threaded screws from FlatFootFox's remix of another sofle case: https://www.thingiverse.com/thing:5443846
thingiverse
This was made because I wanted a more elegant looking case for the Sofle v2, while supporting RGB backlight, a large battery and sandwich mounting. Uses 6 M2 heatset inserts (max 10mm) per side, and 3 M3 heatset inserts per side for the legs. Use...