kenmore pro range replacement knobs 3d models

Designed this to replace the electric knob on my Kenmore Stove. I printed without support on my Ender 3, bit of stringing on the inside but you can't tell when installed The insert in the back is designed to be used without the metal fitting...

Oversized knobs to make polar alignment more precise and more easily. ... This in combination with a little lithium grease on the threads did wonders for me.

I had to create a replacement knob for my Kenmore stove. Unfortunately, I'm not familiar with scanning 3D objects yet, and I don't possess the skills of a CAD expert. So, I decided to take matters into my own hands by modifying the existing knob. I...

The knobs to my Kenmore Elite Grill (Model #: 14116640) were breaking/broken due to age. As these are pretty expensive, I decided to design and print my own. The D slot for the valve is tapered, so they press firmly on. For extra security there is a...

The knobs on my Kenmore Elite Grill (Model #: 14116640) were breaking and broken due to age. As these are pretty expensive, I decided to design and print my own. The D slot for the valve is tapered, so they press firmly into place. For extra...

The washer control dial is specifically designed for use on Kenmore models including the LKA 105 00 L.

A replacement Dishwasher knob specifically designed for a Kenmore Dishwasher is available through Sears, with an estimated cost of approximately $13; order this part from the Sears website...

This is yet another oven knob model. &nbsp;I couldn't find an existing model that matched the one I shattered. &nbsp;</p><p>The model was created in FreeCAD 0.20 and exported to .step format. &nbsp;The FreeCAD file is included in case you want to...

Replacement control dial for a JennAir Gas or Electric range.

Replacement knobs for a Nord Electro, Stage, and Piano keyboards. ...They should work on series 5 and 6 but I'm not sure about others.&nbsp;There are two types:nord-knob: Regular knob with no pointer.nord-knob-pointer: Knob with slot for pointer which...

The replacement knobs aren't exact copies of the originals, so I tried printing duplicates using 3D technology. Unfortunately, the limitations of this method got in the way and I had to make some compromises to get the print right without needing...

Replacement potentiometer and encoder knobs suitable for the Nord Electro 5 & 6 are available, offering a precise fit when printed on a Flashforge Finder. ...However, due to variations in printers, you may need to adjust the scale by 1-2% to achieve a...

This little item replaces the ashtray with a cover that you can put more cigarette lighter adapters, usb or flat switches into

These small plastic inserts replace the original rubber stoppers that fit into the metal scaffolding holding pots and pans in place. I had lost all my originals and opted to use these alternatives instead. They do get hot and slightly soften when...

This is a collection of various knobs that I came up with to replace ones that were damaged or missing from Tek 7000 series scope plug-ins and mainframes. Most of these assume that one has the original knurled aluminum piece with the set screws that...

Designed up this knob for the Sky watcher EQ6r-Pro. ...This is a direct replacement for the altitude lever which will inevitably wear out due to poor design..

... wheel fork, it may require an additional 1/2" nut which I had in my parts bin. The smaller knob is for opening and closing the caliper arms, I warmed up the metal bolt part with a lighter and pressed the knob onto the end of the knurled steel shaft.

... it or grind the threads down so they will fit into the hole.  The left side of the shaft was also very slightly smaller than the right side, so I had to slightly shim the left knob with a bit of plastic packing tape for a tight wobble-free fit.

... grind the threads down so they will fit into the hole. &nbsp;The left side of the shaft was also very slightly smaller than the right side, so I had to slightly shim the left knob with a bit of plastic packing tape for a tight wobble-free fit.&nbsp;

Original Leveling knobs on Xvico X3 Pro is terrible... ...I think everyone will want to either replace them or print an upgrade.

M4 x 40 mm bolts (normally available at HomeDepot/Lowes hardware sections that range $1 - $3/ea) will be needed to make this vat resin knob. This printable handle will work on M4 x 40mm bolts with hex heads. 45mm length bolts both work too ...

... points in the correct direction for my dryer. ...I also increased the size of the knob so it would be closer to my original. This doesn't look like the original knob but does the job. This fits the Kenmore dryer 87160800 and replaces part #WP688865.

Replacement Dishwasher knob designed specifically for Kenmore Dishwashers. ...Order a genuine part from Sears here for approximately $13: http://www.searspartsdirect.com/kenmore-dishwasher-parts/WD09X10004/0022/363/model-36314371791/0582/0130000.html,...

They are also used to adjust the rear height, function as the rear feet, and appear to be used on a number of different brands (Whirlpool, Kenmore, Estate, KitchenAid, Maytag) and models so I've included all these as keywords. It's separated into...

Extra parts needed: M10x60mm bolts and nuts fit the 35mm knob M10x50mm bolts and nuts fit the 25mm knob M10x40mm bolts and nuts fit the 15mm knob All are coarse thread hex bolts with a 1.5mm nut size. ... Important note: Print these parts with the...

Knobs for da Vinci 1.0 Pro. To assemble, you'll need to print two pieces specifically designed for the rear of the device and one for the front. These knobs fit seamlessly into place with a satisfying "click" once assembled. PET-G is the ideal...

This is a replacement for the glass tube on a Seahorse pro

Easy replacement of the filament on CR10S Pro with this part in a few seconds https://youtu.be/LxGfK56k-Ug

In just one week, I managed to break two of these, so I ordered a replacement part. Print Settings: Printer Brand: Printer: Vision 3D Rafts: Yes Supports: Yes Resolution: 0.3 Infill: 25 Notes: When printing this design, it's crucial that...

Frontpanel, Backpanel and Grips for Nintendo Pro Controller, for those who want to customize theire controller or need replacement parts for the original. ... For private use only!