kengan ashura creator 3d models

I'd like to share my print settings with you: Printer - FlashForge Creator Pro, Rafts - No, Supports - No, Resolution - Medium, Infill - 50%. This design prints extremely quickly and efficiently. ...To get the best results, I recommend using a strong...

The edge is angled to prevent the spool from falling off and the spool holder provides a simple, minimalist design that gets the job done. Enjoy! Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Yes Resolution: 0.2...

... as they would fit just as well. I've also included a foot with a glue holder, or you can simply print four of the other foot designs. Print Settings: Printer: FlashForge Creator Pro2016 Rafts: No Supports: Yes Infill: 30% Notes: Printed in ABS.

This accessory securely attaches to the side of a FlashForge Creator X by snapping into the built-in carriage mounts on either side. A hex wrench storage section fits exactly 3 standard 1/4" drive wrenches typically supplied with the 3D printer...

If some of your filaments have larger inner tubes than what the FlashForge Creator can handle with its current spool posts, they should be placed on the back of one side of the spool posts. Users with dual extrusion models will need to print two of...

GoPro Mount for Flashforge Creator Pro. Two arm lengths are available, 45mm and 60mm. This mount will hang from the front of the printer, with a hump in the middle to fit over the screw. (This is designed specifically for those who paid $1,200;...

An honor bestowed upon the triumphant winners of the 2015 First Annual Thingawards Most Featured Creator category, where innovators like no other, truly stand out. ... 1st Annual Thingawards: https://www.youtube.com/watch?v=ltyt6BqPVIE Category Winner...

ServiceTray for FlashForge Creator Pro 2016 fits perfectly into the top hole on this machine, making maintenance of the extruder, fans and nozzles much simpler. This useful accessory is designed to be printed as a single piece, but an alternative...

I'm building a hinge for the dome of my Creator Pro, and I had to get creative since I was tired of constantly moving it around. The design requires blocks to support the weight of the dome itself, which presented a challenge. To address this issue,...

Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: .2 Infill: 15-20% Notes: I strongly recommend printing the pieces at .2 resolution to ensure accurate results. My own prints came out perfectly, with no need for...

I recently acquired an old FlashForge Creator (with the wooden frame), but it was missing some parts - including one of the filament feeder tubes.  I'm not sure what the original ones were made out of, but I had some PTFE tube and fittings on hand...

... This holder is customizable for Flashforge Creator Pro filament guide tubes, keeping their ends at a safe distance from the printer case to prevent entanglement and positioning them at an angle that complements the superior Makerbot acrylic dome.

Walabot sponsored a Hackster.io meeting and provided a free Creator/Maker edition of their hardware. The board did not come with a case, so I was able to design one using the board's CAD files. The case is designed to allow users to easily slide in...

GoPro Mount for Flashforge Creator Pro. Two downward arm lengths available, 45mm & 60mm. This mount will be attached to the front of the printer, featuring a hump in the middle designed to go over the screw that's standard on printers costing $1,200...

This customizable guide is specifically designed to secure Flashforge Creator Pro filament tubes. It elevates tube ends away from printer casing, preventing entanglements and optimally positioning them within the superior Makerbot acrylic dome found...

Handle for FlashForge Creator Pro (year of manufacture 2015 and later) Insert the handle into the long holes on both sides of the printer. The inserts on both sides make it easier to heat up the inside and reduce the risk of wrapping, especially with...

GoPro Mount for Flashforge Creator Pro. This mount attaches to the front of your printer, with a raised section in the middle to fit over the screw. Designed specifically for those who invested in the higher-end model, this mount takes advantage of...

The spool holders that come with the FlashForge Creator Pro (2016 version) are very limited in the dimensions of spools that it can hold. Most of my spools are either too wide or the hub is too small to fit on the manufacturer's holders. So I made a...

Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: 0.20 or less Infill: 25% - 100% Notes: When printing the hanger and knurled knob, add a G-code command to pause the print just before covering the captive nut hole...

... for the newer FFCP, so here we are. Print standing upright with a brim and it should be golden Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: Any Filament: CC DIY PETG

I wanted to use this fan duct on my Qidi printer which is a FlashForge Creator clone that's also a Markbot Replicator Dual clone. To do this, I needed super long M4 screws but unfortunately, I didn't have any and wasn't willing to wait three weeks...

The flashforge creator 3 uses a combined heatbreak and part cooling fan that cannot stand still for longer periods of time. Caused by its combined nature, a long standstill leads to inproper cooling of the heatbreak and thus is not possible. This...

The NOMAD (aka North American Orbital Mobile Aerospace Defense) is a space station appearing in the film The Creator. It took me about 6h to design, and around 40h to print the full-scale model.Lessons learned from my last design (The Starborn...

So I had to purchase the only lid FlashForge provides for the 2016 creator pro, which is the unibody lid. If you're not aware, this lid is 12mm too short to sit properly on top and there are no brackets to secure it in place. As a result, here's my...

The spool holders provided with the FlashForge Creator Pro (2016 version) have very limited dimensions, unable to accommodate most of my spools. Either they're too wide or their hubs are too small to fit on the manufacturer's holders. As a result, I...

I printed a new one today using Hatchbox yellow ABS with support material and got very good results (slicing with Simplify3D). This is a customizable holder for Flashforge Creator Pro filament guide tubes. It holds the end of the tubes away from the...

The hinges on my MSI Creator 17 '21 laptop were experiencing significant stress while in use open in my work truck while doing drone-based surveying of areas with rough roads, to the point where one hinge came apart and had to be glued back together....

Here's a link to that little handle: http://www.thingiverse.com/thing:1241895 My Print Settings Printer - I used the Flashforge Creator Pro, a great printer. Rafts - I didn't need any rafts for this thing. Supports - My printer could handle some...

The spool holders that come with the FlashForge Creator Pro (2016 version) are very limited in the dimensions of spools that it can hold. Most of my spools are either too wide or the hub is too small to fit on the manufacturer's holders. So I made a...

Print Settings: Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Doesn't Matter Resolution: 0.2 mm Infill: 14% Filament: Renkforce ABS Black Post-Printing: If the holes come out too small, use a 3 mm drill for the screw holes and...