keltec p17 optic mount 3d models

Uses 4X M4 - 0.5 (pan head preferred) screws - M930 Optic Rail - Mid: same as the full length rail, but just shorter/ not flush with the front of the receiver, extending one slot past the forward-most receiver mounting screw hole. Uses 4X M4 - 0.5...

There is currently only one version of the optic ready slide (Mount Option A) with more options coming soon. Non-optic ready versions of the slide are coming too. Files are as follows: 1) MKIII Optic Ready Slide (pattern A) 2) Custom blowback unit...

- There is currently only one version of the optic ready slide (Mount Option A) with more options coming soon. Non-optic ready versions of the slide are coming too. Files are as follows: 1) MKIII Optic Ready Slide (pattern A) 2) Custom blowback...

Optic Mounting Rail for nerf Pathfinder no shell cutting needed, replaces the existing rear sight guard wings hardware: 1 5mm x 30mm bolt with a head no larger than 9mm 1 5mm x 40mm bolt with a head no larger than 9mm 2 nuts with 8mm wrench flats...

Optic Mounting Rail for nerf Pathfinder no shell cutting needed, replaces the existing rear sight guard wings hardware: 1 5mm x 30mm bolt with a head no larger than 9mm 1 5mm x 40mm bolt with a head no larger than 9mm 2 nuts with 8mm wrench flats...

These are my optic mount designs for the S&T Type 64 AEG. It takes Mlok rails, the ones that have the 80mm centre to centre of the holes in the rail. The Mk1 is offset to the left by about 10 mm to make it easier to use with goggles. The...

The KelTec CP33 is most accurate at the range, in competition, or for home defense when using a pistol brace or utilizing the increasingly popular “cheek weld “technique. Both bring the firearm closer to the shooters face particularly the “cheek...

This accessory replaces the rear sight on your Beeman P17 pistol, making it easier to cock. ...It's designed for use with a red dot or other sight already installed.

Transform your standard pistol grip into a convenient storage compartment with our Pistol Grip Plug designed specifically for the KelTec RDB.

... 2% in my slicer for a slip fit and 1% for a snug fit. ... The threads work best if you have a tap to chase them but just using a screwdriver to run in a 1/4-20 bolt works just fine. Holes are 1/8 inch for mounting onto light source of your choosing.

This is a helper tool designed specifically for use with the Beeman P17 air rifle. A significant amount of physical effort is required to pump the gun, especially when the seals are functioning properly and not leaking excessively. ...However, this aid...

Voici un levier de chargement à deux doigts pour la Keltec Sub2000. Mon levier d'origine ayant cassé, j'en ai usiné un nouveau dans une barre de 8 mm de diamètre. (ici une tige de vérin pneumatique. On pourrait prendre une queue de forêt, un bout de...

This is a custom-made floorplate/baseplate replacement for the Keltec PF9 magazine.\nUpdate: Added baseplate with extended finger grip. File v3\nPrint Settings\nPrinter Brand:\n Monoprice\n ...

Optics post mounts designed specifically for securing equipment to 1/2-inch steel rods, which can then be mounted to a table or other surface. Two identical mounts are available, one featuring a central hole in its vertical shaft that facilitates...

Detailed versions of the Legrand 057673 P17 IP54 Small footprint Plug Socket

Detailed versions of the Legrand 057673 P17 IP54 Small footprint Plug Socket

I Am Human.

m

Brand New pistol from KelTec, and another 5.7x28mm in just one year(after Ruger 57). ... P50 use FN P90 magazine and really fancy mechanism for it.

Hello, Here is my modeling of a vertical stand for Lenovo thinpad P17 gen 2 laptop. The feet of the stand are made separately to avoid too much support for printing. Printed on cr10V3. ... Vertical stand lenovo

They likely will not work well for a P15 or P17 Gen-2. They could be a bit taller, but the seem to work well. Because they are only 12mm (~1/2") high, I can gently slide the computer around on a table--without leaving them behind. The feet have...

KelTec RDB ejection port cover is designed for easy installation, requiring no modifications to the RDB itself. Simply clip it on and you're good to go. To print this model, make sure to use supports during the printing process. This 3D printed item...

I made this cap to turn the hollow pistol grip of a Keltec KSG into storage. I printed the cap in 2 pieces with PETG. The 2 pieces should be glued together to keep them from seperating. ...I printed it with the click on its side, and the cap with the...

Here is my self-made optics drawing template.

This project is learn the focus of lenses. ... Optical experiments .

You often need to keep things in their proper place, particularly when dealing with KelTec devices. This wrench will enable you to screw the thread-protecting nut securely without damaging its finish. Warning - Use on a cold barrel only! It's...

This is a bolt tube cover for the KelTec Sub2000 Gen 2 carbine. This should only fit the Gen 2 with the polymer tube nut and with the stock fully extended. This does not interfere with the folding action at all. This does not obscure the...

These are magazine cases primarily intended for KelTec CP33 22LR magazines. They can be used for other magazines of similar size and design or for other functions. Resize as necessary. Four (4) sizes are available: 1) single 2) double 3) triple,...

Adapter for attaching picatinny-based devices for KelTec Sub2000 at 45 degrees. This is a simple and easy to quick design that allows the rifle to be folded. Requires 2 m-lok screws and nuts to attach it. I highly recommend buying metal ones and...