keltec cp33 brace 3d models
9370 3d models found related to keltec cp33 brace.thingiverse
The KelTec CP33 is most accurate at the range, in competition, or for home defense when using a pistol brace or utilizing the increasingly popular “cheek weld “technique. Both bring the firearm closer to the shooters face particularly the “cheek...
thingiverse
The KelTec CP33 is most accurate at the range, in competition, or for home defense when used with a pistol brace or utilizing the increasingly popular “cheek weld “technique. Both bring the firearm closer to the shooters face particularly the “cheek...
thingiverse
I found it annoying to remove the mag from my CP33 because there just isn't much real estate to get a hold of. This baseplate is wider than the factory one, especially at the front, allowing you to get two fingers on the mag and your thumb on the...
thingiverse
These are magazine cases primarily intended for KelTec CP33 22LR magazines. They can be used for other magazines of similar size and design or for other functions. Resize as necessary. Four (4) sizes are available: 1) single 2) double 3) triple,...
thingiverse
Gentlemen, I decided to work on some Kel Tec CP33 accessories and this is the first piece, its a P-Rail brace adaptor, I designed 4 versions starting from large and all the way to micro. You will only require 2x M3 x 20mm socket head screws to mount...
thingiverse
This is a remix for an angled grip with a steeper angle, and no rests or rails on the side. ...this is a forward angled grip, it is not intended as a vertical foregrip, it even says so on the side.
thingiverse
This is a PB ( Brace )mount and QD tube for the CP33. It is retained by two small zip ties in front of the sights and around the snap on frame mount. I did not design in the use of the frame screws, but left the detail available for longer screws if...
myminifactory
To Assemble the Folding Tail Hook Brace Adapter for your Kel-Tec CP33, You'll Need to Obtain Several Components: - An M4x30mm Screw - An M3X30mm Screw - A Small Spring with an External Diameter of 4mm or Less - An 8mm x 3mm Magnet For Detailed...
thingiverse
using carbon arrows as shafts . ...I havent worked out a locking mechanism yet
thingiverse
kel-tek cp33 short and long rails i split them to print and super glue together
thingiverse
This is an adapter for the keltec cp33 to use a tailhook arm brace. hardware youll need: the acutal ATF approved tailhook 10mm alumium rods or feel free to made that smaller for whatever rods youwant to use. ... 2small screws 2mm x 8mm for the back...
thingiverse
I designed a Magpul-style baseplate for my KelTec CP33 magazine, leveraging martialmedia's concept as a starting point and modifying it to suit my specific needs.
thingiverse
(this model has not been printed and tested) - CP33 Shroud mlok no rail - This model does not include the area for the igitalnimbuslabs brace rails. If you dont need that attachment then this is the model for you.(this model has not been printed and...
thingiverse
This is a magazine extension for the CP33. I designed it based off of Kel-Tec's proprietary magazine extension. ...It should function just as well as the proprietary version.
thingiverse
This is a magazine extension for the CP33. I designed it based off of Kel-Tec's proprietary magazine extension. It should function just as well as the proprietary version. This is the second version. ...It is slimmer, fits better, and has a stronger lip...
thingiverse
This is a magazine extension for the CP33. I designed it based off of Kel-Tec's proprietary magazine extension. It should function just as well as the proprietary version. ...This is the same as my previous magazine extension, but it has no grooves as...
cults3d
This was originally as a mount for a Bushnell Trophy TRS-25 Red Dot sight to fit on a KetTec CP33 with the original iron sights still usable. It mounts to the picatinny rail, and has one picatinny slot in the middle of the top for the red dot to...
thingiverse
Shroud replaces stock mlok barrel shroud on the CP33. Use stock screws to mount the shroud. The print still provides a mlok slot in the same location. Light compatibility designed for Streamlight TLR RM 2. Pressure pad half installed with shroud...
prusaprinters
This is a magazine extension for the CP33. I designed it based off of Kel-Tec's proprietary magazine extension. It should function just as well as the proprietary version. This is the second version. It is slimmer, fits better, and has a stronger lip...
thingiverse
A design for a replacement buttstock for a keltec sub2000 gen2. please try and give feedback. ...thanks!
thingiverse
This is a gripping accessory for the Keltec RDB, enabling users to securely stow compact tools like bore snakes or other essentials within the pistol's grip. ... -EDIT 11/14/2019 Introduced a sleek, low-profile design option.
thingiverse
A quick fix for the Keltec RDB's side rail involves swapping out stock screws with longer ones - M3x20 work well. The updated design includes left and right rails, giving easy access to the takedown pin, as well as a stronger universal model without...
thingiverse
Simple stick on shell deflector for the KelTec Sub2000. Offers a bit of protection for those of us who are left-handed. Used 3M double sided automotive mounting tape to attach it. The fit is not quite right, although it looks pretty good. I may...
thingiverse
Here's a quick fix for the Keltec RDB: a makeshift side rail that gets the job done. You'll need to swap out the stock screws with longer ones, M3x20 is a good bet. The included left and right side rails will give you access to the takedown pin, and...
thingiverse
angled forgrip for keltec cp33 with thumb rest and rail left and right
thingiverse
Harware needed: 1 - M4 x 35mm bolt (Found at lowes or homedepot in packs) 1 - M4 Nut (Found at lowes or homedepot in packs) Original hardware for the stock mlok barrel shroud, it should be 2 screws Any other hardware to mount an mlok attachment...
thingiverse
Transform your standard pistol grip into a convenient storage compartment with our Pistol Grip Plug designed specifically for the KelTec RDB.
thingiverse
Voici un levier de chargement à deux doigts pour la Keltec Sub2000. Mon levier d'origine ayant cassé, j'en ai usiné un nouveau dans une barre de 8 mm de diamètre. (ici une tige de vérin pneumatique. On pourrait prendre une queue de forêt, un bout de...
thingiverse
Print in flexible filament. ...This will allow for you to mount a Hatori Super Small Mini LED Flashlight at an ultra-low profile on the top picatinny rail of the Keltec cp33, so that it is adjacent to the right side.