kel tec sub 2000 dust cover 3d models

The 3D printing model’s chosen scale is 1:32 for the FFF/FDM version and 1:64 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 142 parts;- A printed model is 168 mm tall, 240 mm wide, 448 mm deep;- Gull-wing...

Be sure to provide enough wire length to connect to the MUTANT base AND fit under the cover exiting the hole in the top of the cover. Extend the loom on the extruder side as needed by 150mm-200mm. Use the heat shrink solder seal connectors to...

Also check out my other designs.You want to use this hourglass as a toothbrushing timer?Have a look at The Tooth of Time - you only have to exchange one of the PVB parts to convert this hourglass to this fancy design:Looking for more PVB-smoothing...

Be sure to provide enough wire length to connect to the MUTANT base AND fit under the cover exiting the hole in the top of the cover.Extend the loom on the extruder side as needed by 150mm-200mm. Use the heat shrink solder seal connectors to extend...

With enhanced speed capabilities through MIPI (Mobile Industry Processing) protocol the developers of the UC9281M1 are aiming at giving total solution that covers any need from system architect designing standalone and embedded camera hardware or...

I made these grooves bigger than the standard gap used everywhere else just for this purpose, but it's still awkward to do… a sawing motion helps. Update: I still needed to cut the grooves even after inserting the tape but it was a lot...

If you want to align knob to various angles, you can use different knob inserts.Knob Cover with Triangle Pointer (3) - Seam position: RandomKnob Cover with Circle Pointer (2) - Seam position: RandomTriangle Pointer Insert (3)Circle Pointer Insert...

Instead, get the washers and nuts for holding the plate to the door started, then push the plate up flush against the cover for the display and tighten down the nuts for the plate. Don't forget to attach the wire guide and the door support string...

The 3D printing model's chosen scale is 1:400 for the FFF/FDM version and 1:800 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 42 parts;- A printed ship is 133 mm tall, 480 mm wide, 469 mm deep;- Assembly...

The skin of the monster corroded and mutilated by the virus is covered in countless ulcers, and is stapled together on the forehead. The Nemesis’ eyes are mere cavities in the skin, and its nose is curved to the side, further the distorting look of...

The 3D printing model's chosen scale is 1/34 for the FFF/FDM version and 1/68 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 90 parts;- A printed model is 648 mm tall, 633 mm wide, 344 mm deep;- Assembly...

With a functioning RC fire monitor and RC-controlled water pump installed, it brings some action to the pool.Major changes as compared to the original model:Scaled to 150% to provide enough space for the fire monitor and a water pumpImproved motor...

Apparently, before it was owned by Lyman Truckenmiller, Truckenmiller Hill was covered in a series of 20x20 mining claims that were hotly disputed and a lot of prospectors killed and robbed each other over gold (or access to potential gold) on the...

Now the legendary carrier is ready to cover one more sphere and become a considerable member of your 3D printed autopark. ADAPTATION FOR 3D PRINTINGM577 Armoured Personnel Carrier 3D printing model is an assembly model and its moderation and...

The meticulous project took the author around 160 hours and resulted in a flaming 3D printing figurine that looks as if it has escaped the comic book cover a mere second ago. Jean Grey is depicted fully corrupted by the Phoenix Force while the...

I will add this link on my project page. CNC with covers size (cm): Z69.5 / X123.4 / Y71 Top surface plate size (cm): X68, Y62 UPDATES 1.0 (2022-07-10) • X cart cable and wheel cart covers added. 0.1 (2018-11-25) • ... </small> </div> ...

The MoonBase magnetic coupler.Note:- If you do not use a riser for the top cover, Do Not print this. It was designed to straighten the filament path and remove the nasty bend that often occurs at the point where the PTFE tube meets the extruder.  The...

&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp; &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;...

The earlier posted configurable floor stand - customized with a “don't touch” message and your name (1250 names are included).Print instructionsPrint without supports, change the filament color at 4.8mm while printing to get a well readable...

He narrowly escapes the creature - revealed to be masked and protected by advanced active camouflage - by unintentionally covering himself in wet mud and thus becoming invisible to its infrared vision. Major Dutch has to destroy the enemy to survive....

Almost the whole surface is covered with the jungle. The whole life of the Yautja is determined by the Code of Hunting. It preaches courage, military skill, and devotion to the clan. A Predator who follows the Code will not hunt or track down a...

I will show you how to construct the part with breadboard slot since it also covers the whole construction of the one without breadboard slot. Make sure to safely remove the support raft at the bottom of the part: After placing the magnets on the...

Most of the ships in this kit are smaller and weirder than others I’ve covered so far, and are sourced from both official [FASA](https://memory-alpha.fandom.com/wiki/FASA) sourcebooks and the semi-canonical FASA published [Stardate...

I used single-row header sockets to hold the Arduino Nano and EasyDriver boards - note that I used strips that covered the whole length of the EasyDriver board. Right-angled and straight PCB header pins were used as appropriate (see pictures) for...

they dont hold a lot of weight so this seems to work pretty well.i think i covered most of the less obvious stuff, of course if you have any questions post a comment, i try to check here every few days.edit:i ordered this...

Fell beasts have large, bat-like wings, their bodies aren’t covered either with feathers or scales and moreover, the flying steeds give off a stench. Their scream is piercing and raucous as if metal clanking - due to this fact the creatures are...

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                      

One part of  Lock (53_Ge_lock_10H_x18) needs to be printed 18 times;- Two variants of cockpit - a solid one and a cockpit with insertable glass designed to be printed with transparent filament;- High-poly cockpit;- Folding front wings with rockets;-...

The glass cover of the cockpit is also provided as three separate files for you to print it using transparent filament. There can also be found special tunnels leading into the cockpit and MegaCaliber Six turbolaser cannon that were designed by our...

This version comes with reactor covers separated for you to print them with transparent filament;- All parts are divided in such a way that you will print them with the smallest number of support structures.DLP/SLA/SLS 1.0 version features:- Contains...