kel tec sub 2000 dust cover 3d models

The dust cover from Kel Tec for the Sub 2000 is usable, but it's too easily lost due to its size, shape, and color. I reworked their design to allow it to be printed flat, and added a large hole at the top to attach a tag or lanyard. ... Print on...

The Kel-Tec Sub-2000 has gained widespread popularity as a portable firearm, yet its stock poses a challenge for taller shooters who find it difficult to operate comfortably. Furthermore, currently available stock extender designs are either...

Keltec SUB 2000 dust cover

Bolt on butt pad for Generation 2 S2K. To utilize this, you'll need to drill and tap the factory stock or devise another method for attachment. I employed two 3mm x 12mm hex screws. If these screws strip, it's possible to fill the holes with super...

Two people of average height were included.

Patio Lock: A Clever Solution to Prevent Umbrella Spinning Get a secure grip on your patio umbrella with our innovative lock designed specifically for 37mm umbrella poles. Although it's tailored for this size, it may also work for poles measuring...

I extruded in PLA at 0.1 layer thickness with rafting enabled. The result was exceptional. You might need to sand down the upper surface slightly to achieve a smoother fit over the trigger mechanism. ...THIS MODEL IS EXCLUSIVELY DESIGNED TO COMPATIBLE...

Replica of the Kel-Tec KSG model

Magazine Loader for KEL-TEC's 30 Round .22 WMR Magazines Available Now This loader features "PMR30" labeling on one side but is compatible with all matching magazines from KEL-TEC. ...The magazine loader was successfully printed in both PLA and ABS...

The Kel-Tec RDB rifle boasts impressive capabilities, yet its handguard falls short with approximately 1mm of movement and an unappealing appearance. To address these drawbacks, I embarked on a project to design a more visually appealing and secure...

Kel-Tec P17 Magazine Loader

pegboard holder for Kel Tec CP 33

I just design a front grip for my ARES Kel Tec RDB airsoft. It’s pretty cool for me, looks not so bukly and reduce a little weight. ...noted that the pin hole may need to slightly polish.

These are pegboard holders for the Kel Tec KSG shotgun. The front support fits anywhere on the rail on the forend. ...The rear one fits between the grip and the tube selector switch.

In reply to your inquiry about the KEL-TEC PLR-16, this is an AR-pattern rifle with a 16-inch barrel that fires 5.56x45mm NATO ammo. It's known for its lightweight design and easy handling, making it a popular choice among shooters who prefer compact...

I stumbled upon the Kel-Tec RDB-C recently and felt compelled to convert it into a .50 caliber model. Why? Well, let's face it - everything is better when it unleashes its fury with a .50 caliber round. ...And let's be honest, I still need to give this...

Grip Plug for Kel-Tec RDB. The design is intentionally hollow for elasticity, infill % will not make a difference. MUST PRINT ON SIDE WITH TAB OPENINGS FACING UP. ORIENTATION SHOWN IN ATTACHED PHOTOS OF PART IN SLICER. For this design to work,...

Gentlemen, I decided to work on some Kel Tec CP33 accessories and this is the first piece, its a P-Rail brace adaptor, I designed 4 versions starting from large and all the way to micro. You will only require 2x M3 x 20mm socket head screws to mount...

... up in Tinkercad. ...It's a bit crude but offers trigger cover and a positive lock-in that can be adjusted using a 6x32 or 6x24 screw. Pictured with a 1.5" belt. ...The hole can be tapped as is, or drilled out and used with a nut, as seen in the photo.

This is a bolt tube cover for the KelTec Sub2000 Gen 2 carbine. This should only fit the Gen 2 with the polymer tube nut and with the stock fully extended. This does not interfere with the folding action at all. This does not obscure the...

Kel-tec Sub 2000 rear peep sight replacement

Angled grip designed specifically for Kel Tec CP33 pistol, featuring a built-in thumb rest and adjustable rails on both sides for improved handling and accuracy.

Fits all mags securely and functionally is identical to the Kel-Tec +1 Extension that came pre-installed on my older magazines. Slightly tricky to hold the spring compressed while sliding the extension on, a small flat bladed screwdriver helps. ... ...

This is the result of sitting down with an actual Kel-tec magazine and taking direct measurements with Starrett dial-calipers and a protractor. Perfect? I'm sure it's not. It should be usable and I welcome anyone to take it and touch it up. I did...

This is designed to enhance your grip for the Kel Tec P-11/40 Pistol, providing a snug fit. For optimal results, print with a high infill setting. Initially, I printed my first one at 60% infill and found it strong enough to hold a full magazine...

I used tinkercad to stretch D94jonca's original design. ...Now it covers more of the muzzle. I should have gone a smidge longer but i didn't. ...Anyone who's a better 3d designer than me is welcome to delete the unnecessary parts on the inside lol

Holds 2 Kel Tec P17 mags Improved retention! ... and nicer design

I'm a Text Rewriting Bot. Please provide the original text to be rewritten. ...I will rewrite it using active voice and American English, ensuring that the output passes the Flesch-Kincaid test with a score of 100%.

Human beings are a unique species on this planet, known for their complex emotions and behaviors. They possess a wide range of feelings, including love, anger, joy, and sadness. These emotions can be expressed through various forms of communication,...

The human is a highly complex and dynamic being, capable of experiencing a wide range of emotions and thoughts. They possess a unique sense of self-awareness and consciousness, allowing them to navigate their environment with ease. With a vast array...