kayak anchor line reel 3d models
174043 3d models found related to kayak anchor line reel.thingiverse
A simple reel handle I made for the custom reel I use for the anchor line on my kayak. ...The reel is a reused filament spool.
thingiverse
This anchor storage solution attaches to the gear track on a fishing kayak and holds a 3lb claw anchor, and provides a hook on the side to hold a spool of line. By putting an eye-bolt at the front, the anchor-storage provides a place to clip the...
thingiverse
Print: two pulleys (linked to below) five guides (or however many you need for your size kayak) one hoop Attached to the kayak using stainless steel screws and plastics epoxy from Loctite. The hoop and guides are my design; the pulleys I borrowed...
thingiverse
THIS A SMALL KAYAK ANCHOR CLEAT WITH ANCHORING SPREADERS ON THE BOTTOM. I WOULD USE 100% SILICONE TO WATERPROOF THIS AREA. ... THE HOLES ARE AROUND 4.5MM I USED #12 X 2 1/2" SCREWS HOPE YOU LIKE IT
thingiverse
I designed this as an inexpensive DIY project to add an anchor trolley to my fishing kayak. You will need to print two shells and one wheel per pulley. Lubricate and glue or just tape the two sides together. ... Note: I used a slightly hooked...
thingiverse
This is a simple DIY kayak anchor weight adapter I came up with that fits a 2.5 lb weight. The base is 1.75" in diameter, the shaft is 1.125" in diameter, and the top hole is .25" in diameter. I made the top have openings to let the air out so that...
thingiverse
i used paracord for line on it because its thinner and is strong! enjoy! UPDATE!! 6/3/18 So i went ahead and modified it to have 4 locking positions via notches on the spool and a small locking pin on the spool guide. I also added a slot so you...
thingiverse
THIS A CUSTOM ANCHOR TROLLEY FOR AN ANCHOR SET UP ON A KAYAK. ...IT HAS TWO 8MM ANCHORING SPREADERS FOR KAYAKS WITH OUT ACCESS TO THE INSIDE. I WOULD USE 100% SILICONE TO WATERPROOF THIS AREA. ... I PRINTED THIS IN NYLON HOPE YOU LIKE IT
thingiverse
Hobie Kayak universal anchor trolley guide. I purchased two genuine Hobie anchor trolley kits for my Pro Angler 14, one kit did not have the third guide in the package. I'm too lazy to call them and ask for one to be shipped. Direct copy of the...
thingiverse
The bottom part is made to fit perfectly in the track of a kaku branded kayak. However it fits in my ascend 10t track as well. ...So if anything needed remixed that should be the only thing!
prusaprinters
This is a remix of https://www.thingiverse.com/thing:4896995 scaled down for a 1.5lb collapsible claw anchor.I printed mine in PETG for longevity. ...I have it attached with a printed rail found here https://www.thingiverse.com/thing:4822543</p>
thingiverse
Acts as the main mounting point for an anchor trolley that utilises bungee cord (circa 8mm diameter will accept smaller and possibly up to 10mm). Easy item to print so settings are open to what ever you want to try, will work with a wide variety...
thingiverse
this is a pulley made for a kayak trolley anchor line i printed last year in ABS is works perfectly may need to invert parts to print without supports
thingiverse
A buffer bead for Kayak anchor trolley set ups. ...For lines up to 6mm diameter.
thingiverse
Printed in PETG. ... A simple printable anchor that will work with a cheap 2.5lb or 3lb weight
cults3d
Printed in PETG. ... A simple printable anchor that will work with a cheap 2.5lb or 3lb weight
thingiverse
A hand line reel for fishing. ... An easy thing to be brought backpacking or left in a vehicle. The double holes allow the line to be tied to the reel. Hold the reel with the hole facing the water to throw a line for casting. ...
thingiverse
A simple reel for storing control line flying lines Instructions It is printed in two parts and then glued together. ...If using ABS, acetone works great.
grabcad
A line conditioner unit, complete with reel, boasts a power capacity of 2400 watts and operates on a 120-volt voltage system.
thingiverse
A simple clip to retain lines on plastic reel for control line model plane lines. I printed mine in yellow PETG, less chance of losing it in the grass......Sized for a reel that is 1.22" wide. As modelled it is a slight interference fit so it stays...
pinshape
A quick little tool to hold tension on your line to run new line. Will need some M3 bolts and nuts. Tighten one side to your rod and then the other tighten down till snug and slowly loosen till the line moves enough to reel it up.
thingiverse
... better. To assemble my reel, I created a loop using the reel holes and wound a section clockwise and another counterclockwise on the reel space. ...The motor shaft requires a flat for proper installation, and I printed mine at a 0.2mm layer size.
cults3d
When using a batereel, prevent the line from going backwards and making it difficult to take it out. ... Fasten the line to the front gap or wrap it around the back groove.
thingiverse
I made a couple of mods to the original. ...Added a line guide to the top and strengthened the attachment bracket. ...Also made it longer so iit would fit a standard commercial line pack.
thingiverse
This is an achor cleat designed to replace a pad eye. Can also be used to dock. Print out of PETG/ABS so it holds up in the sun. High infill recommended. ...
thingiverse
I made a simple line (silon) hand reel for my daughter for kiting.