kapkan 3d model

This is because it is a slide on design to limit the complexity of the model.  INSTRUCTIONS: I tried my best to make this the simplest adjustable optic for nerf yet! As such it has only 3 parts that can easily be printed in under 2...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Thank you very much and happy printing!Updates13/02/2022: Redisegned T-Slot-Clip so that the PTFE tube does not interfere with the cables on the side of the Raspberry Pi (see picture below).PrintingLayer height: 0.2 mm;Material: PETG (recommended),...

UPDATE 09.08.2022 •changed length for diffusor and mount from 10mm to 100mm •orientation changed for some models •added end cap UPDATE 12.08.2022 •added with diffusor / without diffusor comparison photo and electronics box wiring photo •added...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

# What you'll need This will work with any CH340 USB-serial chip I think, but the model here is for the CH340N for USBC. A picture of the exact chip is given. I ordered one from AliExpress for about $3, and one from eBay for about $6 (because it was...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

2022-04-14 I started to create a new base that could use threaded inserts and quickly realised the base models had become quite complicated due to the iterative design process, so I went back to basics and recreated them. The new housing mechanism is...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

It features several small niceties, such as a water inlet that optimizes top-water removal, using magnets instead of suction cups, a 'vacation' mod for skimmer waste overflow, snap-on piping for secure fitting, and much more.Please note that this is...

The Version 1 is based on the original model, but with added material to compesate the extended face on the striker, and the second one is something I made because one of my magazines was giving me trouble, not really stoping when it needed. See what...

... The single-blade model can be reversed in most slicer programs to cut from one side or the other of the 120 film, as described earlier, in "Preparing This Tool." The OpenSCAD source file therefore lacks any provision to make this adjustment. ...

In short, it means that we will be using the Name Tag creator  to make the base (and thus be able to add text, image files, &c), and then create fitting covers and holders in this program. (A mixed approach is to also create the base with...

I was unaware that the MMU2S required changes to the extruder and almost decided to hold off and just install the SPA by itself, but I started poking through the assembly manual for the MMU2S and realized there were changes that needed to be made to...

I found printing 16 a time eventually one clip would pop off and ruin the batch, the ears add enough bed adhesion to keep any from popping off, and it makes taking the pieces off the bed easier. Comments greatly appreciated, let me know what you...

or it will sag and make contact with y-front/back-plate !)4x P-112-MINI-y-carriage-bearing-strap.stl Print settings:3 Perimeters4 top/bottom layers0.2mm layer height40% infillMay require custom support(brushed support enforcer in prusaslicer works...

Average those two altitudes, to get your result (we rotate and average to cancel out any errors due to the ring not hanging perfectly straight).Avoid windy days if you can't move out of the wind, as the ring blowing around reduces accuracy...

The Gryphon is a mostly 3D printable, hobby-grade, Nerf semi-automatic flywheel blaster. Its main design features are as follows:Uses 130 to 180 sized 20.4mm , brushed DC motors.Semi-auto by rack and pinion with 1:3 gear multiplication. The trigger...

 I only buy something off the shelf if I can't make it myself! All parts except the acrylic, rubber grommet, and fasteners are 3D printed.IMPORTANT NOTES:This will only work with the USB port relocated to the front LCD display - or using the new...

The grey color blends in nicely with the color of the grouts of my wall.4x screws 30mm x 3.5mm (+ 2 extra for version with customizable adaptor)4x screws 16mm x 3mmShort iron wire to be used as axis for front hinge2x screws 60mm x 5mm for mounting to...

Align top frame width from the 200x400 sheet slots if needed.Mark screw locations on the top frame, drill and install screws (M3x16)Add metal rod pieces to the hinge between top frame and front sheetGlue magnets to 28 SL1S enclosure front bottom mid...

There is now an uploaded drilling guide that takes that into account. Update 8: The long awaited instructions document is now uploaded! Update 9, uploaded an updated Taz 6 specific endplate. There are several other related projects that are...

A challenging learning toy … but perhaps also a clock for the one or other adult 3D printing fan.I got the inspiration for this project from a contribution on Thingiverse (https://www.thingiverse.com/thing:2852026). I completely redesigned the case...

... loading filament on each lane to test if the chamfers cut on the smaller tubing is enough to prevent the filament from getting stuck, and to see if the small tubing is seated correctly. Rechamfer/reseat as required Category: 3D Printer Accessories

Cómo configurar los parámetros para personalizar la impresión del soporte de maleta para silla de ruedas V2 2.1. Para poder personalizar el soporte de maleta deberá tener instalada en su ordenador la aplicación para diseño 3D OpenSCAD. Se trata de...

3D Printing is about beauty and design. When storing the filaments visibly, the storage should at least satisfy some degree of beauty. When designing parts to be printed, you also need to take care of the print process: The print should use as less...

A take on norwegiancreation's PID ball balancing seesaw using an Arduino.Video of this...

If you encounter any layer separation or odd layer squish patterns that were not there before, ensure that the anti-wobble is not allowing any movement in the Z axis direction and adjust accordingly to make sure the pins cannot move up or down. ...

Print instructionsCategory: 3D Printer Parts Summary I've been enjoying using the stock inductive Z endstop as a bed probe on my Artillery Genius, but was suffering a bit from its temperature sensitivity: I was noticing that at different times of...

*helps: complicated objects, not designed for 3D printing* **Raft layers** `(2-4)` can not only help with bed adhesion but also can help with technical prints where even first few layers need to be accurate. When you add a raft all the first layer...