kac rail 3d models

The gun has a standard 21mm rail, I once attached a $3 scope from China just for the sake of the optics! The optics are not part of the project. What is needed: - 3mm screws and nuts (I will provide a list on request) - A 7mm spring, about...

Just tiny misalignment of the rails rods and/or the bearings makes unnecessary friction. I found out the hard way that the H formed bed holder was not properly aligned from the factory and I needed to loosen all the screws on it to make it nice and...

The main Purpose: Build a 3D printer from 20x20 aluminum extrusion that is fully scalable to at least 600x600x600mm without any further change than using longer rails and longer profiles for the frame. The printer should be able to achieve real-life...

The existing brackets held the lead screw 25mm off of the back edge of the top rail. The Pillow Bushings were just under 14mm from bottom to the lead screw center. So I created these shims/mounts to move the center of the bushing bearing out to match...

OPTIONAL: Screw on the Picatinny rail. 5. Screw on the tip. 6. To close off the blaster with the battery, put on the slide (frame top) and secure it with a pin and snap on the detent in the back. 7. Don't forget to screw on the grip panels with motor...

My design combines both designs and provides a mount for E3D Hemera on a MGN15 linear rail like the one in the Ratrig V-Core Pro with belt tensioning and support for x-axis endstop and BLTouch. For attaching the BLTouch please follow the...

The dimensions of every CR10 hotend should be compatible but the default (non-"all metal") hotends are designed to be used with a bowden tube inserted deep into the cold side, which is a problem for this mod.Other mods on my Voron V0:The Ultimate...

I'll also very likely change the support in the power and ethernet port, since I have no idea what I was thinking supporting some of that circular hole…added a version of the control box with with built-in supports since I couldn't get Cura to do...

This older version left for reference _______________________________________________________________ In this version, the part that attaches to the MGN12 rail has been redesigned to be a single piece, to simplify assembly. With the previous...

I also made a storage slot for them on the top structure.I used a DIN rail for mounting all of my electronics on the back and 3D printed a cover for the high voltage portion.I bought a small LED light bar from Amazon and afixed it under my top...

I was inspired by the MPCNC when I stumbled upon it, and I liked how they used electrical conduit for their guide rails. However, I wanted something a bit more straightforward in design, and I wanted to incorporate lead screws into the mix. As it...

ASSEMBLY  1] print the case 1             2] print the gauge and put it in the rail            3] print the disc...

I have had my printer like this for some time now using an aluminium panel on the rear with all the electronics hanging out back but I wanted to make it safer and more compact, so I have kept the fundamentals of the design, but moved it within the...

More info can be found here: https://hackaday.io/project/173854-3d-printed-high-torque-servogearbox-version-2 Components used: 11 × 3D printed componentsCan be found on Thingiverse 1 × 775 brushed motorlink:...

18/03/2021 Update new files listed as v4, it has had some changes to strengthen up the right side to avoid it breaking by moving the display over a bit more central, its adjusted so it will sit flush with the bottom of the machine and flush with the...

Make sure that all DI of the LEDs starts at one of the 2 LEDs and goes around in the circle till the other 2LEDs strip at the end (See arrows on the led strip in the image) Connect all of the strips with wires (reference the image again) Test the...

I could also print some angle brackets and tie them to the rail for extra stability. I might also be making further mods to the case itself to make it look cooler than a square box. For now, I don't want to deal with any more supports than needed. I...

Entry and exit doors in particular must be touched by everyone entering a household, are usually touched before having access to a sink, and after potentially touching public handles, railings, shopping carts, elevator buttons, ATM's, money, gas...

When this structure is done, the basalt 3D printer will then be moved from its location in the spacecraft to the agriculture / construction dome, where it will be attached to longer rails, allowing it to print the smaller-sized structures. When...

The stock M5x12's should now be fine *Moved slightly the mounting holes to better spread the stress *Tweaked the built in supports V5 - YOU NEED TO PURCHASE AN M5x40 screw for the right hand idler bracket ALL - You need 4 x M4 Bolts / Screws (per...

No additional hardware, bolts into linear rail block as per original. *<strong>Top_Cap_Simple.stl</strong>: Motor and BMG mount. Bolts to the top of Y-Carriage. No add-ons *<strong>Top_Cap_ZipTie.stl</strong>: Motor and BMG mount. Bolts to the top of...

Elements have been carefully organized according to a defined layering system (highway, rail, buildings, water), facilitating intuitive navigation through the scene. Some buildings/houses remain omitted due to import restrictions imposed by the...

Both had minor errors that possibly causes them to print badlyUpdate 20.11.2023:-32 and 35 is the same, but the file for 32 is flawed and therefore gets deleted.If you like my work please consider supporting me on Patreon.Become a Patron!Some of my...

Just search for F10-18M to find them.https://www.aliexpress.com/item/32911485541.html?spm=a2g0o.store_pc_allProduct.8148356.1.d9b947ed4WW4DIPrinting Instructions&nbsp;Print the arms with 3 perimeters and 30% gyroid infill from PETG, ePAHT-CF or...

However, if you have an Ender 5 (Plus) or other Creality printers, you might want to check out my rail sliding mount for the Hemera. What you need: - Four square nuts inserted into all four holes on the Hemera - Four M3x8mm screws for attaching the...

 There's also a "clip" that can be attached to the top back of your printer (on the top back rail, between the z-axis assembly and the y-axis limit switch) to keep the hot-end cables in place.  A cover keeps all your cables tidied away, held in place...

cv19-rp-out-brkt now has a place for a 4x2mm magnet in the center rail. Removed the clutter of the SKP files. If you want them, let me know. 4/8/2020: I have added filter brackets for a paper towel filter (pptl) and made the filter so that it fits...

Base Mount is a file with 2 parts, they are indipendent one from another, u will need to temporally remove the v-rail cover to mount them. Bed Mount is perfectly compatible with the original piece, and it goes in stead of the original cover that...

I have also uploaded a revised version of the bowden type (version 1) with a slightly lower nozzle rail. This has the fixed Led visibility but ONLY if you leave one nozzle port clear. So if you want to use a bowden tube 'and' have the filament...

https://www.amazon.com/gp/product/B00F2IQNX8/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1 Rods:...