kabab fpv 3d models

Okay FPV peeps, so we know vertical is the way to go for RX antenna mounting for the 915 + 868 mhz systems if you're going long range or steady cruising. I hated all the mounting options for T antennas no matter how hard you try you're never...

Initially intended to house a small pan-and-tilt FPV camera, it was ultimately repurposed as a housing for a GPS antenna. The casing is meticulously crafted to snugly enclose a Happymodel GPS antenna powered by an M8n Ublox receiver that came with...

Tired of looking at the standoffs in your FPV feed? well here is a DJI camera mount that moves the camera forward just enough to get then standoffs out of view. yes you will loose a little bit of protection on the camera but I did put a thick ring on...

All you need is a rubber ducky antenna or an FPV video antenna that you no longer need and two pieces of 83.3mm copper wire to make a dipole. Solder one part of the radiating element to the positive (center wire of the coax) and another to the...

I use 4s battery from my FPV drone, i charge the battery only to max 4V per cell (4x4=16V). I use two 4S batteries ( must be 2 identical battery with same voltage !!!) each 4S, 75C, 1600mAh ) connected in parallel, it gives me discharge current 240A...

I made the source mount by AndyABG in TPU and it fits great but found that in a crash, the rear part of the mount that grabs the 2fiddy top plate would come loose and the camera would rotate forward and down in front of the fpv cam. This put it in...

Equipment: - APM Mini + GPS + Sonar - motors 2216 / 810kv - ESC 30A - propellers 9443, 3-blade Carbon Folding Propeller 9445 (for Phantom 2) - FPV Tx - OSD Mini - 5200 mAh 4s - 2 axis gimbal - cam Firefly Q6 The weight of the aircraft without a...

Additionally, I designed a few frameparts with mounting platforms for the GPS-antenna, a gimbal, telemetry or fpv transmitters etc. My prototype, as shown in the pictures, only weighs 840g! AUW with 4800mAh 3S LiPo is 1250g. There are two versions...

This is a 600TVL micro camera tilt mount for ZMR250 frame, SG90 servo controlled, designed specifically for FPV custom build quadcopter. The camera itself can be found in many stores (e.g. Banggood), boasting small dimensions (12.5x12.5mm) and an...

The 30mm to 20mm stack adapter is offset towards the back to give more room for wiring and the FPV camera. It also has little bumpers around the holes that face down, protecting the board underneath from screw heads. I only use three of the four...

Later, I will also create a small snap-on platform for the frame that will carry my small 5.2 GHz FPV transmitter and battery. UPDATE 25-01-2017: I updated the frame to version two. It's a more improved and printer-friendly version of the frame. I've...

... 5 (Should also fit Runcam 5 and other cube cams with same size) - GoPro Naked Version from BetaFPV Thanks to Artur for letting me use his pictures and testing the Session Mount. His thingi Page https://www.thingiverse.com/art_fpv/designs

Currently, it features an FPV system and has a green & white color scheme. The source of most components can be found in the Crossfire II file, except for the antenna mount, which is in the Antenna Mount file. The quad was designed using Sketchup,...

This is a Tripod Mount for the Flir Exx(bx) camera series.There have been complaints that the original tripod adapter accessory was both very expensive ($50) and yet not very stable.Therefore created a cheap and stable version that anyone can 3D...

MODI to use a FPV camera in actual space to inspect the exterior of a ship or space station, thereby reducing the risk of astronauts having to perform space walks. Major Tom will agree that this concept has real potential! Assembly instructions are...

For my latest FPV mini quad build project, I sought out tubular carbon fiber arms to utilize. As a result, I created a custom set of motor mounts specifically designed for 12mm OD tubes. Given that the most widely used motor sizes in the 200-300mm...

You can view my other FPV-related prints by checking out my portfolio. If you appreciate my work and would like to support me, feel free to leave a small donation - I'm not doing this as a full-time job, but hobbies still require time and resources!...

Take a look at my other FPV-related prints if you're interested. ----------------------------------------------------------------------------------------------------- Feel free to show your appreciation with a small donation - I'm not doing this...

You can buy one here: https://www.banggood.com/Flsun-Q5-3D-Printer-Kit-200+200mm-Print-Size-Supprt-Resume-Print-With-TFT-32Bit-Mainboard-or-TMC2208-Slient-Driver-or-Colorful-Touch-Screen-p-1591796.html?p=E01411629100201406T1&custlinkid=1312467 More...

That can be found here: https://www.prusaprinters.org/prints/96509-41-gear-set-for-fpv-rover-20(NEW UPDATE 9/2019 - METAL SHAFTS ON GEAR CARRIER w/BUSHINGS)I built a Rover 2.0 & incorporated the changes made by escexed in his "Planetary Gearbox...

For my setup I am using: Long version frame \250mm top and bottom plates\; B19 cheap fpv camera(19 mm) + TS5828S 600 mW VTX; Motors - T-motor F40 pro III; Props - Hurricane 51433-3; Jhemcu 40A 4 in 1 esc(30.5x30.5); Holybro KAKUTE F7 Mini V3 (20x20)...

Any amount of support is greatly appreciated :-) paypal.me/BrianBrocken Feel free to take a look at my other designs: 3D printable antweight battlebot: Bulldog: https://www.thingiverse.com/thing:4623536 SpaceX inspired edf rocket:...

Many FPV pilots mount their batteries on the strap of their goggles, but if I was going to use a bigger battery, I wanted to carry it on my belt, as I felt there was already enough weight on my head with the goggles themselves.I'm not alone in this...

Original file was malformed and causing errors in some slicers. Update 5: Added "upgraded-optional-gopro_fpv_plate.stl" as an upgrade to the old multipurpose FPV plate + GoPro shoe. This package is now more rigid and strictly designed to be pared...

My build on Rotorbuilds for my full parts list: https://rotorbuilds.com/build/27266 Video on the frame design: https://youtu.be/CI2ykUmTqy4 Flight Footage: https://youtu.be/bSuooiEz3OQ Recommended parts: Flight Controller and ESC - [DarwinFPV F411...

Hi, These are parts to build a sturdy cubic tower gate perfect for FPV-racing or freestyle flying. The holes are designed for 20mm tubes, and for locking purposes, you'll need to drill a hole through the collar and tube. Use a locking pin as you...

В самом быстром режиме ходьбы робот потребляет 10-12 Ампер, + 2 ампера для габаритных огней, фонарика и FPV камеры. Значит аккумулятора на 8 аЧ, который тут установлен, хватит примерно на 30-40 минут, это как минимум. ... Список комплектующих: 19х...

Recently got the DJI HD FPV setup and upgraded my quad with the CaddX Polar Vista. Wanted a nice clean way to mount the Vista, and the stock frame is far from suited to it. I could have mounted the Vista to the top side of the top plate, but I...

A FPV Cam housing specifically designed for the IC120SHS camera is also available at Hobbyking. For a smooth flying experience, I recommend using: Motors: 1306, 1407 or 2204 (I prefer smaller motors myself) ESC: FVT Little Bee 20A, similar-sized...

EDIT 04/01/2014: Please check out my new quadcopter - Fearless (thing:218726) This is a quadcopter which I have designed from scratch for general hobby flying or FPV. Modularity was foremost in my mind while designing it and therefore everything...