k40 z bed 3d models

x301/x201 MOD to 4 linear rail for z-axis with this MoD you can also add 2 more z motors. with the added support the x-axis should not bow in or out as much allowing you to increase the size of the building area. As well as have the ability to G34...

Use layers of varying heights - 50 microns, 100 microns, 200 microns, and 300 microns - when slicing the model to verify that the print bed lies completely flat.

A versatile bed support designed as a substitute for the standard 12mm Z-Axis, perfectly compatible with the 2020 Rail Bed Frame and aluminum bed plate of the FilaFarm system.

Greetings all, To connect a D4 endstop with the auto-leveling servo, I've created this design. ...Combining zenmaster's z-probe and a D4 endstop holder. Once completed, I'll share photos soon. ...Have fun!

This spacer is specifically designed to adjust the Z-Axis stop height when using a borosilicate glass plate on top of the metal build surface for Qidi Tech X-one2 printers. It securely fits onto the back of the Z-Axis platform between two metal rods....

Activator for Sapphire S, a derivative of Chris Kissling's original design, perfectly fits this bed model. You can purchase it at kis3d.myshopify.com/en. Print the activator with support from your 3D printer's bed. To assemble, use two M3 bolts that...

Discover the ease of automatic bed leveling using Hall-Effect sensors! ...Watch this informative video at http://www.youtube.com/watch?v=UPeNtwEEcww to learn more about this innovative technology.

Cabled chains have been custom-made to fit inside the FT-6 printer, securing both the bed's AC power supply and thermistor wires in place. ...Utilizing standard 10mm x 10mm Amazon cable chains, these modifications were implemented with ease.

You will need to slide your z-endstop/switch back slightly on the frame and then attach the "z-stop pusher" you printed onto the screw that hits the z-endstop/switch (see...

This is a spacer for the Qidi Tech I and X-one2 printer that adjusts the Z-Axis stop height when using a borosilicate glass plate on top of the metal build surface. It fits snugly on the back of the Z-Axis platform in between the two 10mm metal rod...

... adjustments to the mounting position or sensor orientation to achieve optimal performance. By following these simple steps, you can effectively install a bed level sensor on your Anet A8 3D printer and enjoy more precise prints with less hassle.

... with a fresh spin. ...I managed to snap both original pieces in two while attempting to put them together. So I turned the print orientation by 90 degrees, and that gave me significantly better stability in the crucial areas around the z-axis.

I upgraded my Creality Ender-5 with a sturdier stepper motor to counteract gravity's pull on the bed when the printer is idle. The stock motors lack sufficient torque, causing the bed to sag under its own weight. This issue worsens when printing on...

Credits: TowerPro SG90: http://www.thingiverse.com/thing:1164679 Prusa i3 Hephestos: http://www.thingiverse.com/thing:371842 Robo 3d Auto Bed Leveling: http://www.thingiverse.com/thing:301715 AutoLevel with Servo and Photosensor:...

... bracket i could no longer use it becase the wheel screw on the x gantry was in the way. ... This remix accounts for the screw while maintaining the proper lenght for the glass bed and the m4 nuts like in the original design.

This accessory enables precise adjustment of the Z-axis endstop found on Tronxy Prusa i3 clones. It employs a screw and spring mechanism, allowing users to raise or lower the endstop by simply turning a screwdriver. Although this design still...

This is a two-piece reinforcement bracket specifically designed for the Z-stepper motors on the Anet A8 printer. It's part of a comprehensive set of printable reinforcements that have not yet been published. The lower section, highlighted in red,...

This is a custom mount specifically designed for the LJ12A3-4-Z/BX sensor, tailored to be securely fastened onto an extruder plate. The clever design makes use of two linear bearing screws from the x-axis setup. Not long after, version 2 of this...

... Most important value is the distance between X-carriage's top to the bed, when your hot end is touching it. Print the mount. You'll also need to print the microswitch holder. Follow your firmware instructions to set up automatic bed leveling.

... rest, making everything even more solid. This setup will provide a long-lasting hold on the rods and prevent the metal plates from bending over time due to the weight of the bed. ...It also allows for greater stability and eliminates vibrations.

This is a remix of the Z-probe holder designed by Michael Zenner, creator of thing #167430.\nSince not all extruders are identical, the lever length is adjustable and customizable.\nEither M2.5 screws and nuts or a small nylon tie can be used to hold...

Minimal support is needed.Ender 5 Plus - Print on the side opposite the PCBA connector opening. These models are tailored to Ender 5/Pro/Plus which have been converted to the ZeroG Mercury One CoreXY system.Ender 5/Pro version mounts to the rear...

... show how off center it was before the print. ... I would not recommend restraining z-rod on more than two points. ... If You want top and bottom stabilization, You could make the nut "free" with this model: https://www.thingiverse.com/thing:5137480

Under Bed Load Cell based Z-Probe Under bed load cell Z-probe. It's somewhat a mixture of JohnSL's and palmer23's. What’s needed: - STM32F103C8T6 board. I’m using a “black pill”. Any Arduino compatible board could be used, but those * pills boards...

So starting off with why I performed and took the time to discuss my upgrade experience: I finally got fed up with the z wobble where the axis of the previous 5/16-18 tpi embedded stepper motor rod was bending due to stress and fatigue over a few...

K40 laser panel

K40 Laser Alignment

Adapter for K40 Fan 50mm

Fabrication d'un connecteur de courroie pour la réalisation du lit électrique de la Laser K40 2 x Vis tête bombée cylindrique à empreinte hexagonale M3*8...

Einfacher, verstellbarer Halter für einen Microschalter um den Deckel des K40 Lasers abzusichern (Laser EIN nur bei geschlossenem Deckel) Zum Anbringen mit doppelseitigem Klebeband oder zum Schrauben. Anbringen des Microschalters mit zwei m3x12...