k40 upgrades 3d models

I designed left and right bed holders for K40 laser cutter engravers, specifically tailored to fit my Orion Motorworks 40 watt laser. This design allows me to modify the bed without removing the gantry, giving me added flexibility when working with a...

I created this hinge for my K40 laser as it did not have a hinge that can be locked at a certain angle for my Camera to be used with Lightburn. This file has a pair of them for both side but you can cut only one if you do not want to install it on...

Hi, This is a custom laser table designed for K40 or other lasers. I purchased one initially but found it inadequate, so I redesigned it entirely. You can also find this design on Amazon or eBay. The blue parts comprise an 8mm thread rod, cut into...

Automated or manual operated Z-axis bed for K40 laser ( can be used for other purposes as well) using Nema 17 stepper motor (pancake) can be automated with ESP32 and stepper drivers , or by any other means Print Settings Printer Brand: Prusa Printer:...

That i am using for my k40 laser extractor. It takes the stock inlet outlet and sizes them for a 4" flex vent using the stock outlet hardware. as for the inlet i used 3mm brass thread inserts and foam to attach it to the housing. You can cut out...

As most K40 owners know, the metal exhaust duct is too long and tends to intrude into the workspace when you want to use the entire serviceable area. ...I didn't want to get out the Dremel and cut a hunk of it off, so I worked this up.</p> <p>You will...

... set Width to 0.500 mm, then press Enter. Do the same for Blue: 1=0, 2=0, 3=255, 4=255. Black: 1=0, 2=0, 3=0, 4=255. Now you can save it under....... Next, close Inkscape. Then open K40 Whisperer and Open Design File, now you can laser this part!

This project aims to create individual components that can be assembled to support a motorized, honeycomb z-bed designed specifically for the common K40 laser cutter using a Makerbot Replicator 2 with high-speed PLA printing. Currently, only the...

This is a fast and simple way to exhaust your K40 outside through a double hung window. I mounted the blower on the exterior so that any leaks in the exhaust tube will be on the suction side rather than blown out into the room. It's quite...

I created a custom drag chain for my K40 laser because the standard one I purchased was interfering with its travel limits. The initial design came from this thing: https://www.thingiverse.com/thing:8239. I made some modifications to suit my needs....

Adjustment Tool for K40 Laser with Original Head and Lens (50.8mm)\r\nUse with a Adjustable Platform, of course\r\n\r\nChoose the Right Tool Based on Material Thickness (Stated on Tool) and Place it on X-Axis. ...Then, Align Other Part of Tool with...

Got a K40 laser cutter. I wanted a drag chain for my air and red dot laser. Well none fit my needs. Also my laser cutter happens to have a door hinge which doesnt allow for other chain setups. SO i design this. Made it with the ability to easy...

I wanted to be able to chill the water for my K40 laser if necessary. If the water gets too warm, I simply place a frozen half-gallon of water in the bucket and it will cool it down quickly. Assembly is straightforward. Just cut a hole in the bucket...

This is a three-part system for directing your K40 laser to a 3-inch hose. All parts are designed to be removable externally for easy access and maintenance. Once you replace the old internal exhaust, you can insert the new shorter one, followed by...

This is a custom-fit exhaust system for a Chinese K40 laser setup. To assemble, first print the exhaust flange on your 3D printer and then cut out the mount using your laser cutter. The design calls for the flange to be securely attached to the rear...

So you want to add a milliammeter to you "digital" K40 but don't want to make such a huge hole. This bezel allows you to make the smaller hole and use the bezel to both fit the offset meter parts from the panel and gives a smarter finish. You don't...

... mm and press Enter. Do the same for Blue: 1=0 2=0 3=255 4=255 And for Black: 1=0 2=0 3=0 4=255 Now you can save it under a new name...? You can now close Inkscape. Next, open K40 Whisperer and Open Design File. ...Now you can laser this thing!

The optional gasket is a precise 1mm thick and fits perfectly between the port and the K40 chassis as well as between the port and the duct. For added security, two gaskets can be used or you could create your own by tracing out a paper template or...

This is a ring mount for the Chinese K40 style lasers. It sets atop and around the laser head and is secured with a latch. There are no screws in this design, so no trips to the hardware store. There are three ball joint recivers mounted to...

This is the air assist nozzle I utilize with my K40 laser cutter. The design was conceived in OpenSCAD and I have included the OpenSCAD file that can be modified to suit individual needs. The coiled hose and fitting I employed are listed below for...

My K40 laser doesn't have the most square gantry and I've adjusted it as best I can. I found it still deviated about 2mm left-to-right and front-to-back. I took inspiration from how many 3D printers level the build plate and designed this manual...

I've finally got round to aligning the mirrors in my K40 laser cutter. Using the <a href="https://k40laser.se/lens-mirrors/mirror-alignment-the-ultimate-guide/">mirror alignment guide</a> on k40laser.se, I needed to raise mirror 2 a little to get the...

Also I found the pitch/lead being a bit low.it could be a bit wobbly due to the placement of the pulleys at each corner and to how the threaded rods were constrained by the beltthe stepper support felt a bit weakno built-in way to compensate for an...

++Design for air assist for this plate available in my Things++\r\n++File provided does not have the 40k engraving on it++\r\n++Meant to be cut from 3mm Acrylic or other 3mm material++\r\n\r\nI've battled alignment issues with my K40 for months now.

check version 2 I found that the original design and manufacturing of the original K40 laser Carriage is not so good I made a first version : https://www.thingiverse.com/thing:4738689 but after many versions i designed this one : I designed a new...

I have used this on 3 K40's and it works perfectly, yest it takes a little more time but you get a 100% alignment, that means you will use less power to cut and will get a nice finish on the edge of your cut once you turn down the power levels. ...

I searched thingiverse but found none that appeals to me and whose parts will fit in my K40 Laser. So I started constructing my own rack. I can fit a DINA4 sheet in my laser cutter. So no part should exceed 210x297mm (roughly 8.3x11.7 inches). I...

My take on a motorized Z table for the ubiquitous K40 Chinese laser is a low-profile design that takes advantage of the confined space in the laser. Min/Max heights (as built) are 1.5 inches and 4 inches, respectively. This allows for easy removal to...

For those of us who cut a hole in the bottom of their K40 laser to fit a rotary tool, this may be useful to change the height of the laser. These legs replace the castor wheels which are a hazard anyway. Legs let you change the height of the laser...

I was tired of the original exhaust setup for my K40 laser so I made and printed these things, they kick ass! Either will fit into the back of the laser in the factory slots, and can be used in either up/down or right/left orientations. Very low...