k40 mirror 3d models

I whipped up a tiny mirror mount for my K40 laser cutter. ...Initially, I encountered issues syncing mine and the official manual suggested that my mirror was set too high, prompting me to craft a smaller version than the flimsy metal bracket that came...

I've finally got round to calibrating the mirrors in my K40 laser cutter. Using the mirror alignment guide on k40laser.se, I needed to elevate mirror 2 a bit to get the alignment spot on. I attempted using washers, but that was just too cumbersome...

I've finally got round to aligning the mirrors in my K40 laser cutter. Using the mirror alignment guide on k40laser.se, I needed to raise mirror 2 a little to get the alignment perfect. I tried using washers, but that was just too awkward for my fat...

This has a diameter of 50mm which is the normal width of a K40 tube, Now if your mirrors and tube are completely misaligned pop your tube in the holders, screw down, test fire the laser and see if you can adjust your tube or the mirror to get the...

So you decided to upgrade your K40 mirrors from those badly machined holders with blemished mirrors to those beautifully anodised (blue or yellow) and precision machined parts you see advertised online as replacements. It even has an "air assist"...

So you decided to upgrade your K40 mirrors from those badly machined holders with blemished mirrors to those beautifully anodised (blue or yellow) and precision machined parts you see advertised online as replacements. It even has an "air assist"...

When setting up your K40 laser cutter, you may need shims to align the mirrors correctly. These precision shims measure 0.05 inches in thickness and include washers for the laser head as well as shims for mirrors 1 and 2. They took approximately 10...

Use this precision tool to check your mirror alignment on number three.

This is a breakout of the K40 1st mirror holder. I did not name them, all the parts needed. ...

Alignment tool for K40 mirrorNo need more for putting tape over the mirror and risking getting the mirror dirty. You can fire a couple of pulses, simply move the strip over a little bit to get a fresh piece of paper.Three versions:direct on the...

Aligning mirrors requires precision and attention to detail, which is why having a dedicated mirror shroud is essential. This tool not only shields mirrors from dust accumulation but also provides an ideal perpendicular surface for alignment...

I designed an improved second mirror mount for my K40 laser, as the original one was significantly off-center, making proper alignment nearly impossible without makeshift adjustments. ...I fabricated this custom mount to replace the standard issue...

A tool to remove and replace mirrors and sometimes lenses in K40 or similar laser cutters that use 20mm fittings. You'll need two M2 screws at least 6mm in length (but longer ones work). It's set up so you can use a 17mm wrench, 6mm allen key or...

I got fed up with my K40 laser trying to align the mirrors and having a bit of tape stuck to it and mucking up the laser... i also found the bent bit of metal inadequate and carried a lot of vibration which in turn affected the sharpness of the...

I got fed up with my K40 laser trying to align the mirrors and having a bit of tape stuck to it and mucking up the laser... i also found the bent bit of metal inadequate and carried a lot of vibration which in turn affected the sharpness of the...

This is a remix of DIY3DTech's: eBay Chinese CO2 Laser Cutter & Engraver Mirror Alignment Tools https://www.thingiverse.com/thing:1149832 To improve on the original design I did the following: 1) Redesigned it using OpenSCAD. 2) Measurements can now...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/ehL6BAJFYvS

My machines second mirror requires a slightly lower position than the factory part, so you may need to adjust the shim depending on your desired height. Materials needed: 2 x M3x18mm screws, 2 x M3x10mm screws. ...The original part was somewhat...

Adjustable bracket first laser mirror K40.

This is a customized mount for the K40 laser's second mirror, built to replace the flimsy stock mount. The K40 stock laser cutter comes with a sheetmetal mount that has a tendency to flex up and down, much like spring steel, whenever there is rapid...

Instead of checking alignment with a test fire of the laser every time I fiddled with the mirror(s), I mocked up this laser module holder so I could get real-time feedback from my mirror adjustments. There are channels on either side of the plug for...

Instead of checking alignment with a test fire of the laser every time I fiddled with the mirror(s), I mocked up this laser module holder so I could get real-time feedback from my mirror adjustments. There are channels on either side of the plug for...

To safeguard the glassy surface of the mirror from scuffs caused by the loosening screw of the mirror stand.

Here's a simple holder for a mini 6mm laser diode module that fits snugly into the tube of a K40/equivalent CO2 laser engraver/cutter. There are channels on the side where the laser module wires can exit the tube and connect directly to a battery.

Had to install an auxiliary mount for the second mirror, which is attached to the X-axis gantry, since its initial position was too low, making it impossible to center the beam. ...Feel free to customize this design using Fusion 360 as needed.

this is a first laser cutter mirror mount for a k40 laser cutter recommend printing with 100% infill

This if for a Chinese K40 laser cutter my first mirror mount mine got bent so my friend clayton fox knocked up a design for one big shoutout to him

3D model of the first mirror mount designed for K40 laser machines. This mirror mount should be placed adjacent to the CO2 laser tube. To add a mirror, it must be 20x3mm in size. I have made every effort to create an accurate model that can be...

Links to products: Cloudray individual parts: https://www.cloudraylaser.com/collections/laser-head-mirror-base-1/products/lc4060-laser-head-blue-12-18-20-50-8?variant=12871497383987 Cloudray lot of all three:...