k40 air assist nozzle 3d models

Air Assist Nozzle for Chinese 40W Laser designed to withstand intense heat without degrading or catching fire when placed near the cutting point. It excels at suppressing flames and blowing smoke away from workpieces, allowing users to operate a...

Here is a very simple adapter I made to connect the Genmitsu air assist nozzle to my existing 5w laser focus ring. ... For whatever reason, the opening on the Genmitsu nozzle is obnoxiously sized when compared to typical focus rings used on many lasers.

This is my version of the air assist nozzle for a sculpfun S9 laser engraver/cutter. Print it with supports only touching the build plate and it should come out ok. I printed mine using a 0.2mm nozzle and PLA+ filament. Its nice and air-tight and...

Air assist nozzle for NEJE 40watt laser module. I redesigned https://www.thingiverse.com/thing:4884993 to fit the Neje 40W (15W optical) module. You can use a push-fit or any other 2.5mm hose connector, or even drill it larger. I also...

This is an Air Assist Nozzle to be mounted at the TwoTrees Totem S Laser Engraver. It is used to provide airflow to the laser lens for protection and clearing smokes and fumes. The piece was designed to be screwed in with 4x M2.5 screws that use...

This remix will fit to old version of Sculpfun S6 Laser modules and thee air assist available wont fit. ...This is a remix from David_J that based his work on the design by Nunu57

It is setup to use a dual output aquarium pump. Note that the left air line connection will bump into the laser frame if auto homing is used, but it will just askew a bit, and can be tappe back into place. I have stopped using autohome, because...

This is a nozzle I made for my Creality Falcon 5w laser engraver. I could not find something like it and couldn't find models that suit me. I used 2 exit 120 lt aquarium pump to test it. I had to drill a hole on the side of the laser cover to...

... for a snug fit. Fuel line designed for R/C gas models is what I used. Line measures 4.6mmx2.61mm by about 5 feet to a barb on my air compressor. very clean cuts with 20-30 psi and 1 pass in 6mm plywood at 200mm/s. Printed with standard resin. ...

I reworked this original fan holder case to fit inside my K40. It should fit any of the "standard" chinese models, but YMMV. FWIW, I got mine in 2021, not sure if they vary at all over time. This fits a standard 80mm fan and wedges in between...

I printed at a resolution of 0.2 millimeters per layer height and utilized a 0.4 millimeter diameter print head.

Printed @ 80% infill .2 layer height. Added screw holes (3.5mm) to hold in place on your machine. ... Accepts standard airhose Standard 1/8" BSP (its an 8mm thread)

Printed it a few times. ...Is a snug fit so needs to bee adappted to you 3D printer

So I mashed together two designs: the long air assist tube design and a cone-shaped lens based nozzle from Scorch's air_nozzle_V1.scad file, shared by the K40 Whisperer. And voila! It has a .14mm diameter hole feeding the air into the lens nozzle...

https://www.amazon.com/HUNST-K40-Laser-Head-Assist/dp/B0BTVLBVJJ/ref=sr_1_30?crid=R1VMHV0A6097&keywords=k40+nozzle&qid=1705102943&sprefix=k40+nozzle%2Caps%2C155&sr=8-30The chain mount is just for that. If you need to mount a chain for the air assist...

This is a compressed air assist nozzle for the well-known 40w Chinese laser, commonly referred to as the 'K40'. It delivers a directed stream of compressed air directly at the lens. The included 55mm lens benefits from this configuration. Female...

This is an Air Nozzle for my cheap DC-K40 Laser cutter. Inner diameter is 26mm. I put a 6mm silicone tube on it! ...The diameter of the connection is 8mm, so that the tube sticks to it very well.

This is an air assist nozzle for the New Genmitsu LC40 10watt laser engraver.

This is an air assist nozzle for the New Genmitsu LC40 10watt laser engraver.

Although the merged air nozzle design has its benefits, it lacks stability and can become detached due to its friction fit attachment method, posing a significant risk to the lens. This upgraded version rectifies this issue by employing an M3 screw...

I wanted to install air assist on my K40 laser but after conducting research decided not to use the nozzle type assist. Instead, I connected a pump to some tubing and then hooked it up to a brake line. This was very easy to do and ensures that the...

This text describes an air nozzle designed for use with a cost-effective DC-K40 laser cutter. It features an inner diameter of 26 millimeters and has been fitted with a 6 mm silicone tube. ...The connection to the tube is secured by an 8 mm diameter...

This is an air assist assembly for the NEJE A40640 laser module. ...This is designed to work with the Precise-Airflow Air Nozzle Sets. https://www.mcmaster.com/air-nozzles/precise-airflow-air-nozzle-sets/ The 2 pieces are glued together with CA.

... 3d print part for Air Assist. ... We designed in Fusion 360 and printed a custom made nozzle for air assist. No screws or bolts are needed, just the 3d part a 4/6mm tube for aquariums and an aquarium air pump. ... Print without supports or raft.

Nozzle for Air Assist compatible with Creality Cr-Falcon 10W 2 screws needed, same as the belt holder (there was 2 loose in my kit)

... 1mm above the item to be engraved or cut. So the end of the nozzle is 19mm below the metal housing of the laser. [edit] improved quick change version on https://www.printables.com/model/207924-sculpfun-s9-quick-change-air-assist-nozzle-improve

Air Assist Nozzle and Dual Line-Laser Holder for K40 Style Chinese Laser Cutters Works with Inexpensive 12mm Line Laser Pointers Found on Popular Auction Sites This Design Combines the Best of Two Great Concepts, Resulting in a Seamless Experience. I...

Air assist input blows out smoke from lens, clearing obstruction for clear image. Two outputs are used: one directed at middle to remove haze, another focused on focal point from side. Bottom part slides onto lens holder, allowing distance between...

This is my air assist nozzle for the 5.5w Sainsmart fixed focus diode laser engraver/cutter (BLUE MODULE) Fits 4mm air tube - no screws required as it sits snugly over the brass cover (as per pic)

The blackTooth laser's nozzle required a 'girdle', which is a piece that press-fits onto the nozzle cone, to enable the air compressor line to connect with the air assist nozzle properly. This accessory ensures a smooth friction fit for the air hose....