k40 air assist diy 3d models

This air assist for the Longer Ray5 10W module uses only two 3M screws to hold it in place. I used some 4mm Inner, 6mm Outer air hose.I printed it with a raft to help hold it down and you don't need to use supports if your printer has good...

Unfortunately, I did not find any air assistance model that could simply be connected to an aquarium air pump. That's why I designed my solution that suits me and is easy to connect. It was important for me to maintain an approach to laser sharpness...

Board for adding air assist to M50 ATOMSTACK module Fitted in place of the original glass, connected to a 4 mm ID hose. Available in two versions, closed or open. Can be connected to a tank compressor, regulating pressure between 0.5 and 1 bar.

Air assist nozzle for NEJE 40watt laser module. I redesigned https://www.thingiverse.com/thing:4884993 to fit the Neje 40W (15W optical) module. You can use a push-fit or any other 2.5mm hose connector, or even drill it larger. I also...

I printed and tried various air assists for my laser engraver but I found most of them too bulky so I chose the solution proposed by Tine Sedej (https://www.thingiverse.com/tintek/designs). ... To the laser anchored support...

Got the air assist for M1 love the magnetic nozzle but I don't feel safe, leaving the grease open to all the dirt and smoke, so I designed the cover so the nozzle can still be removed and the blade holder stays in place, personally, I haven't need to...

(See remake by @gerhardbooysen for the NEJE 40watt module here: https://www.thingiverse.com/thing:4892305 ) After testing different solutions for air assist for my NEJE laser module, I found that the nossle system on my CO2 laser was the best...

I am experimenting to improve the airflow of the fan of my cubiio2 with an attachment which simply clips onto it. A first test of the "air assist1" shows a slight improvement while using the laser to cut 2mm plywood. "Air assist2" has yet to be...

and since I wanted a simple and equally effective solution that is compact, I designed this Air Assist. Depending on the version, either 2 M2x8 or 2 M3x8 and 2 M2x12 or 2 M3x12 screws are needed ( whichever 4010 fan is used) to attach the fan and...

This is an air assist nozzle for the Longer Ray 5 Laser engraver. It accepts a 6mm outside diameter tube. Note: after installing this nozzle, you can no longer use the aluminium spacer to calibrate the laser. Instead, you have to measure from the...

brass tube for air assist tube 1 - 2 ft length of 4mm ID clear air tubing (and air pump of choice) 1 - m3 x 10 bolt and nut 1 - m6 drill tap 1 - 5/32 drill bit (9/64 is slightly smaller but could work for nozzle hole in length and side) Drill the .8...

Simple rear mounted air assist for the Ortur Master 2. The mounting bolts can be re-used on the fan mount, but you will require a 12v 50x50x15mm blower fan and a couple 25mm bolts and nuts to fit it. The stock mounting bolts are just barely...

This is an Air Assist Nozzle to be mounted at the TwoTrees Totem S Laser Engraver. It is used to provide airflow to the laser lens for protection and clearing smokes and fumes. The piece was designed to be screwed in with 4x M2.5 screws that use...

So I decided it was time to start shopping around for a new supplier who might have better air assist systems in place. That's when I stumbled upon Epilog, and their setup really caught my eye. I figured I'd give it a shot, so I set out to recreate...

It is the new S9 model which has a black metal insert to create an air assist effect (poor) My S9 laser has a 19mm cavity that receives this insert. My piece should also fit the older S9 models if you have a 19mm cavity. The standard 4/6mm air...

This is a set comprising of air assist nozzles with the following outlet diameters and clearance from the focus. This version has handy size labels embossed on the nozzles, a free version is also available on thingieverse without the embossing. :-)...

The air pressure is not just building up inside and goes wherever there's less pressure but directed outside. There's separation between the laser path and the air path inside. Make sure to set the focus BEFORE installing, as you won't be able to...

Side assist nozzle, to fit on an extension tube on a G8 Lense

Using a larger fan (20x25mm outlet) and a 3D printed air cone dimensioned to suit the fan's flow and pressure capacity (air guide and outlet not being too narrow nor too wide) you get a good strong airflow. ...

... shows a slight improvement while using the laser to cut 2mm plywood. "Air assist2" has yet to be tested. Disclaimer: I do not know if the increased air resistance will damage the fan or overheat the laser diiode: use at your own discretion.

Each of these nozzles has an intake for an 8mm air hose, which is then funneled into three channels blowing into the laser target area. This design results in a sufficiently high air velocity to keep the cut really clean. ... Note: Calibration of the...

More to 3d themes: https://www.facebook.com/groups/3ddruckercommunityd Air Assist mod and honeycomb grid for the Atomstack A5 laser cutter The fan mod is used instead of two spacer sleeves for the controller board of the laser and inserted into the...

This is a remix I did, created a gap to allow for smoke egress. ...Modified the hose input so it is more vertical. Nozzle also 1mm shorter for a bit more air gap for smoke

I liked the design of this thing https://www.thingiverse.com/thing:4729176 but it didn't fit my laser module and I already had a standard air compressor for airbrushing so I pulled the barb off the end and replaced it with a .8 nozzle. The tubing...

Here is an alternative to an air pump to add an air assit to your S9 laser module, using a 5015 blower. You'll need to thread the two bottom front holes of your laser module to be able to screw the mounting system and the duct, with - 2 x M3x14...

This is a remix of https://www.thingiverse.com/thing:4692711 I made this because the air nozzle was too high for my laser, I have reduced the height so the aim is where the beam focuses, 2mm below the shield.

You can add compressed air to the tank through a port to get faster responses from your system. The tank side fitting is 3/8 MNPT, and the air valve side fitting is 1/4 FNPT. You can use any standard 1/4-inch schrader or fill-style valve with this...

This is a remix of https://www.thingiverse.com/thing:4692711 I made this because the air nozzle was too high for my laser, I have reduced the height so the aim is where the beam focuses, 2mm below the shield.

Sculpfun S9 Left Air AssistModified for efficient functional usage. This component has been used daily for 2-3 months without any issues. This was created to improve on currently available designs. Use of other open-source designs led to the...

you must add a small extender (10mm) to the limit switch to allow it to home properly, easy to make if you own a LM2 (---- I added a photo of what the extender would look like ---) This device mounts to the focus ring, so you need an alternate way to...