junsi 4010 3d models

The two 4010 fans directly blowing across the mcu works a treat and I can feel the air flow through the vents on the other side with the acrylic panel fitted. May need to change them to Noctua fans or maybe install the SKR2.0 I have to actually...

The other uses a JST to connect to the 5V [Noctua 4010](https://www.amazon.com/gp/product/B00NEMGCIA/). 5. I replaced the OEM power switches from the adapters with panel-mounted micro switches. Both wire to a [DPST...

Not available when posting.)5015 part cooling fan (link)6x M3X102x M3X15 + safety nuts or standard nuts with loctite2x M4X25 + nuts1x M3X18 + washer11x M3 threaded inserts - 4mm long (link) What will be reused from stock printer:Titan...

It will take about 8 hours and 45 minutes and about 70 grams of PLA. InstallationTo Install this fan duct you only need 2 M3 screws that are already holding the original fan shroud and for the hotend (4010) fan you can use original screws too...

The 4010 axial fan for the heat block cooling can hit the printer's steel frame. The Y-Axis touch pad goes on the right, front, end of the X-Axis bracket so that the limit switch is activated 4mm earlier. There are a few M3x5mm brass inserts and...

голова опустилась на 7,5мм) и теперь вентилятор 4010 на обдув радиатора хотэнда стал вровень с металлической скобой. При этом область печати нисколько не пострадала, а даже выросла на пару миллиметров. Также появился вариант креплений с вплавляемыми...

 It will be like a custom piece of art that filters the air in any space you need!!! I may add some storage or wall mounts to the design at a later date.  SO NOW TO THE FUN PART!!PARTS: ACTIVED CARBON PREFILTER Amazon.com: Universal Cut to Fit Carbon...

Due to the sideways mount of the extruder stepper motor I will have to design a new angled 4010 duct to make sure it clears the stepper and allows room for cables. I do not use levelling sensors but there are other variations which you may want to...

Due to the sideways mount of the extruder stepper motor I will have to design a new angled 4010 duct to make sure it clears the stepper and allows room for cables. I do not use levelling sensors but there are other variations which you may want to...

Due to the sideways mount of the extruder stepper motor, I will need to design a new angled 4010 duct to ensure it clears the stepper and allows room for cables. I don't use levelling sensors, but there are other variations that you may want to try...

The insert can be replaced with a PTFE push fitting, but a push fitting is pretty much unnecessary and just adds to the hassle of changing filaments.The 4010 axial fan for the heat block cooling will hit the printer's steel frame without the Y-Axix...

Files *superfang-plate.stl - Backplate to attach everything to the printer *superfang-plate-bl.stl - Backplate with BLTouch mount (untested!) *superfang-clip.stl - Small clip to fasten the backplate on the right hand side *superfang-duct.stl - Hotend...

Fan box for the 4010 Noctua is adapted for the noctua fan. (5V Noctua NF-A4x10 PWM) !!! A 4 wires version must ne used ! (pwm signal) like this (5V PWM) ...

Currently, I have only designed 2 fan ducts, both using 5015 blower fans, though I did mock up some 4010 fan mounts, which I have included as step files in the zip archive. My ender 3's configuration files can be viewed here: ...

A small, quick container shaped like a cat, which prints in spiral vase mode in two parts and uses about 3.5 grams of material. Things you could put in a cattainer:at least a dozen paper clips3d printed clipsemergency advil supplyscrews3 pieces...

Best to splices and add connectors to everything to shorten the wires to a minimum.one screw to mount the PCB to PCB_holder_2 before mounting it to the setup (uses 3 more screws, two M3x6 on the right side into the metal plate and M3x8 or possibly...

#####The two versions: + 3015 cooling fan version *Which is for the original biqu fan, this is untested by me.* + 4010 cooling fan version *Which is for the original creality fan, this is the version i'm using. Has kind of a funnel as the fan is...

## MKS Gen-L V1.0 - The undocumented lights, starting from near the fan connector (Yes, their labels are odds then evens), are: - D1: Fan on (flashes rapidly when not at 255/255 speed; dual Creality 4010 fans just twitch and don't turn until...

The added weight compared to the original parts (4010 radial fan and stainless steel shrouds) is +24 grams With the 5015 fan and the assembly screws (V3.5 version, without LED holder and accelerometer). Print: Positioning the pieces on the tray...

Description I designed very rigid and simplistic direct drive mount for my TwoTrees Bluer V2. I haven't found a solution that fits V6 hotend and have proper 5015 part-cooling fan. My main goal was to use a minimal number of external parts and keep...

if you want to do as little as possible to quiet the ender 3 v2 neo down, my suggestion is swapping out the 4010, to a quieter 4020 fan. and placing the printer on a slap with foam under! The Noice doesn't travel through walls anymore. Update...

This remix involves the base unit (2 versions), dual 4010 fan duct and the dual 5015 fan duct. The dual fan duct also has 2 versions - one straight and one offset to 5 degrees to clear the motor. The parts in this thing are based on the standard...

Files *superfang-plate.stl - Backplate to attach everything to the printer *superfang-plate-bl.stl - Backplate with BLTouch mount (untested!) *superfang-clip.stl - Small clip to fasten the backplate on the right hand side *superfang-duct.stl - Hotend...

The housing is sized to fit either the standard 4010 hotend fan, or a 4020 double thick hotend fan.If using a 4020 hotend fan, use M3x22mm panhead machine screws. The 5015 Blower fan can use either a single M3x20mm or M3x22MM panhead machine screw....

V4.2 : -made the mid bolt tab larger, more robust and easier to print -slotted the wire hole for the front fan So you can fix 4010 or 4020 axial fans of your choice. With tool less push pins or M3 bolts. Built-in recesses for the M3 nuts (5.5mm wide...

Parts list: (2) M3x10 to mount to ABL sensor bar (2 or 4) M3x16 to mount 4010 fan (2 or 4) M3x25 to mount 4020 fan (stock metal cover will not fit, off by just 1 or 2mm) M3 nut for each of the above screws used for me I also used 1 M3 lock washer...

Currently, I have only designed 2 fan ducts, both using 5015 blower fans, though I did mock up some 4010 fan mounts, which I have included as step files in the zip archive. My ender 3's configuration files can be viewed here: ...

Electronics 1x Bigtreetech SKR 1.3 mainboard 4x TMC 2208 Stepper driver 1x BTT TFT24 or BTT Mini12864 display 1x Mean Well LRS-150-12 Power supply 1x SSR Relay 8A - Hoymk SSR-D3808HK 1x 16mm anti-vandal power momentary switch - 110/220V variant 1x...

Holds: * 1 x 4010 Fan for Hotend Cooling * 1 x 5015 Blower Fan for Parts Cooling * 1 x BLTouch * 1 x Dual-Port Parts Cooling Fan Duct Hardware required: * 2 x M3 10mm screws. for the screws in the left side of the plate. * 3 x M3 6mm screws, for...

I mounted the "Led Stripe Holder for Petsfang Ender3/CR-10" mount by attaching it to the bottom two screws of the 4010 heatsink fan and upper right corner of the 4010 heatsink fan. The previous stated M3 screw lengths take into account the...