junkrat 3d model

1x M6 square nut - model allows for 5mm thick, 10mm square 1x M6 set screw (10mm length recommended) Important: while printing you MUST put a pause at the layer just before the nut is covered up. Look for the small "box" cavity in-line with the...

Find it according to your vacuum cleaner model. In the file, you can also adjust all necessary parameters, including the angle for the vacuum cleaner adapter. Copy these values into the snipper file as well, since the first section's angle is needed...

Will require manual tapping. Base Base_Type - The type of base (round or rectangular) Screw_Hole_Diameter - The diameter of the screw hole Screw_Head_Diameter - The diameter of the screw head Screw_Head_Countersink_Angle - Screw countersink angle...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

Project: Playdough Tool Design Challenge Overview & Background: Through this lesson, students as young as five years old can be introduced to 3-D modeling and desktop fabrication, with an emphasis on its ability to provide solutions to everyday...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

Infill doesn't matter because the model is a hollow shape. The filament must be elastic and reasonably heat-resistant. I have tried this in NinjaFlex which seems to work well. Anything much harder than Shore 85A is likely to be too stiff to act as a...

 I've included 3mf project files from PrusaSlicer so you can see how I ran this model on my printers. UPDATE 27/01/2022: Created a rudimentary mount to hang the chassis under a shelf or table.  I decided to make a second unit to move...

2)The plastic for the case is about 0.5 kg (the lantern is large, it was made for a large candle) 3)2 hinges for caskets 15x21mm with self-tapping screws (included, sold on marketplaces) 4)a handle for the casket (you can print it, but I wanted...

As far as assembly is concerned, it's all pretty self-explanatory when you see the models, but here are a few tricks: Use as little wire as possible, but make sure you use good wire. The wires run from the grip and back, across the side of the...

... Very basic stress testing was done in Fusion360 with a model of a 1.5" PVC pipe sleeved over the mount and it seems like it won't snap too easily. ...In real life testing, it holds a ~7lb antenna easily.</p> </p></div></p></p></p> Category: DIY

[Medium Sized Model - 25mm base] [Presupported in 32mm and 75mm scale]   Raised as a commoner, Artorian never expected that one day he would rule from the divine seat of the Nirloom that soared so high above the streets he grew up in. Some would call...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

For other sizes of tube or different grid arrangements, you can use the Thingiverse Customizer to remix your own version (the recommended way, so others can benefit from your work) or download the model and use the OpenSCAD Customizer (available in...

Larger or smaller screws can be used if you scale the model accordingly e.g. M3x8 screws at 150% part scale. Note: it's cheaper per screw if you buy in bulk from a specialist supplier. There are two versions of the container available, the standard...

Would like to thank Okef256 for the original model. &nbsp;It doesn't seem to get much attention, but it is great.</p><p><strong>Modifications:</strong></p><ul><li>Modified mount to attach to Ender 5 mount plate instead of linear rails.</li><li>Added...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

After sanding the putty flat, paint it using model paint or cover it with a large sticker to conceal any imperfections. Test fit the Laforge diversity module into the hole where the old receiver used to be. Cut off this standoff because it's...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

Here's an updated model! Some people mentioned that it was too difficult to print with certain materials as it wouldn't handle overhangs. The new update has a split version that can be printed in two separate pieces with full supports that can be...

The COMPLETE Dumlok Flameseekers bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: 12 Dumlok Flameseeker (modular figures + figures with helmet)The Dumlok,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

Enjoy :) Update 04-05-2021: Adding ender 6 models, upgrading all to V4.3 (slotted mount holes for 2mm height adjustability) and adding "fan duct up V2" which has integrated grill. It's more tricky to print because of the small features so i'll leave...