jordan 3 back tab replacement 3d models

After replacing my X axis Belt tensioner I decided to change my Y axis belt tensioner too, since the printer had looked half baked in my eyes :D Yet again another Quick'n Dirty remix of Cornaly_Cool's design. Thanks mate.. You will need to use the...

... ... So I made a new one wich replaces the original one. I made it of 2 parts for easy printing. Assembled without additional material. For protecting the flat cable i also put some stripes of duct tape to it (see pic.) Fully optional. ...

This is a "bowden" PTFE tube assembly replacement that is intended to limit the amount of flex and reduce friction on the filament as it is fed into the extruder. With the help of the 3DS filament "hack" non 3DS filament can also be used. The...

This is a "bowden" PTFE tube assembly replacement designed to limit the amount of flex and reduce friction on the filament as it is fed into the extruder. With the help of the 3DS filament "hack," non-3DS filament can also be used. 3DS...

Nike Jordan Retro 4 Keychain

Jordan 4 sneakers 3D model

I recently encountered an issue with the pop-up vent fan in my 1990 Airstream motorhome, which ultimately disintegrated and left me without a replacement option. Authorized Ventline dealers seemed unfamiliar with the specific fan model when I...

Front and Rear Crossover and MU housing for the Aristo-Craft Alco RS-3 locomotive. ...Part # 22200-64 equivalent.

Front and Rear Crossover and MU housing for the Aristocraft Alco RS-3 locomotive. ... Part # 22200-64 equivalent.

I constructed a replacement in two variants. Both can be printed without support material. The normal version is simply printed standing up and can then be used directly. After printing, a 6mm x 35mm hexagon is glued into the "Hardcore" version. I...

Filament guide for the Ender 3 S1 / S1Pro Can be bolted on at the same place as the runout sensor with the stock bolt. ...

... over the PSU case. I friction welded the two parts together for added rigidity but you could also use any adhesive like superglue or 3DGloop to hold them together. It uses the original screws and mounts back onto the PSU just like the OEM part.

The post on the magnet holder on my Park Tool chain scrubber snapped off, so I measured everything and designed a replacement. It fits mine perfectly with enough tension that it won't fall off but I can still pull it off if needed. If yours ends up a...

The post on the magnet holder on my Park Tool chain scrubber snapped off, so I measured everything and designed a replacement. It fits mine perfectly with enough tension that it won't fall off but I can still pull it off if needed. If yours ends up a...

I couldn't locate a suitable replacement online, though buying another valve and discarding it while keeping the handle would have been an affordable option. Here are the Fusion 360 model and STLs for your reference. I printed using Simplify3D at...

BR-STD-3 unfortunately breaks away after some time. Simply cut open the proximity token, remove the round token from the center and place it in a new housing.

I made this model as i removed the filament sensor because it caused too much friction when printing tpu, since on retractions the filament would bend instead of going back through the sensor, it would falsely trigger, stopping the print. With this,...

Take heed of the following caveat: attempting to service or replace parts yourself may put you at risk unless you possess formal training or hold the necessary clearance from authorized technicians or personnel responsible for conducting warranty...

I accidentaly broke two of my Ender 3 v2 neo fan blades when i was cleaning so I tried to fix it using this one: https://www.thingiverse.com/thing:4731510 and it doesnt fit so i made some adjustments to fit in the ender 3 v2 neo. To install,...

This is a derivation of MrTeliP original Ender 3 Pro SKR Mini E3 Case. He was gracious enough to make the STEP file available which made the editing rather easy. I removed the openings from the cover, as I didn't want filament to fall into the case,...

This is a derivation of MrTeliP original Ender 3 Pro SKR Mini E3 Case. He was gracious enough to make the STEP file available which made the editing rather easy. ...I removed the openings from the cover, as I didn't want filament to fall into the case,...

If you have misplaced or dammaged your Ender 3 or just wish to reduce the number of vitamins to redice weight it is using (especially if you intent on taking it to the planet Mars), you may want to consider extruding your own extrusion (as yet...

One of the legs of my Cherry MX-Board 3.0 broke, so I designed a new one because I couldn't find an existing design. Don't forget to print it with supports. Print Settings Rafts: No Supports: Yes Resolution: 0.1mm Category: Office

I modified holes in the brace so that it would fit seamlessly on my Creality Ender 3. In fact, this modification might make the brace compatible with several other printers featuring a similar aluminum frame design. When you decide to enclose your...

Remixed this to fit on the smaller bed of the Ender 3. I accomplished this by bending the strap up at a ~35 degree angle. I don't know if this is going to work yet. I have a few prints in the queue ahead of this, but I'll let you know how it goes...

http://www.thingiverse.com/apps/customizer/run?thing_id=158717 Settings Options Used: US Inputs, Single Unit Inline Connector Type, 2.0 Wall Thickness Output Dimensions in US Units 1 Output, Strength Setting of 100% Setting Input Details Input...

Screw holes are 3-5/16" (84.1375mm) apart. Feel free to modify and do whatever you will with the files. Just don't sell them as your own. I have tested rev1, but tightened up the screw holes 1 mm for rev 2. Roll the dice and pick one! ...

The holes on the shroud line up with the 3 existing holes in the kit base.This probably works with any of the screw off diffuser style light kits with a 3 hole attachment keyhole base.I know it's ugly and I don't care. ...It allowed me to ditch the...

It still has the same attachment, which fits perfectly into lawsy's extruder for the solidoodle 3 (http://www.thingiverse.com/thing:47561), but I've stretched the hole to hold a sharpie. There are two files: one holds the end part of a sharpie and...

I made 3 designs, 1 with no hole for a switch, 1 for 16mm switch, and 1 for 19mm switch. ... You can take the no hole version and put any sort of hole in the front that you want :) Switch: ...