joint lighter case 3d models

> - Push antenna screw through top-hole (if used) > - Screw ball-joint WITH finger-screw in between to the rear casing with 2x M2x5 screws > - Run cables through rear casing, and connect to esp board (5v top right, GND right below, AI-thinker board)...

king size joint case with a pattern. not easy to get good quality, there is a problem with surfece and stability is challenged at the top. ...please share ur results and comment what can helpnew version is available for sale...

Joint Holder with cap. ... Prints in Vase mode (Spiralize) IMPORTANT: Wall width 0.6mm

I added more material to the joint to prevent breaking issues when connecting the two halves.

So I really like the case that Aaronroma made (http://www.thingiverse.com/thing:2067529) but I wanted the screen to be right on the edge of the table. I used the free stand but it kept sliding all over the place so I designed a table clamp for it...

I reinforced the joint with additional materials to eliminate breakage risks during connection of the two assemblies.

The package includes two sliders, each allowing you to push up a joint individually, providing complete control over the smoking experience. The lid glides smoothly across the top, sealing the container shut when not in use. ...If you have any questions...

Joint Holder with screw cap.This design prints in Vase mode (Spiralize mode). IMPORTANT:To make it print strong enough, use the following settings in cura, this works even with a 0,4mm nozzle. ... Line width 0.6mm Spiralize Outer Contour: ON

... thermometer, allowing me to replace its batteries easily. It also made sense to change the type of connection between the base and the thermometer to a ball joint, which now lets it rotate freely with a satisfying click whenever it locks into place.

For this print, of course, no support is needed.This sleeve is designed for slightly thicker (8 mm filter) and larger (up to 120 mm) joints. If you prefer to use 6 mm filters, and the filter does not stick out of the paper, you can use a smaller...

Instructions Using the following options: coverThickness=2, lidInsetOffset=0, rimInset=1, tabSize=1.5, interiorLength=95, hingeThickness=0.3, interiorHeight=50, lidInsetHeight=1.5, interiorFillet=3, hingeWidth=30, hingeFillet=4, sidewallWidth=2,...

Using a natural ABS material and a Prusa I3 printer, I set the extruder temperature to 230°C with a 0.4mm nozzle diameter. The heated table was made of aluminum with a Kapton surface at 110°C. To ensure quality, layers were printed at 0.3mm height...

This design is perfect for either everyday carry or camping trips, as I've personally checked the options available on Thingiverse and found them lacking in durability. ##Note: No raft or supports are necessary. !!!Note: I'm always open to...

“The best there is”

I'm thrilled to share this fantastic design for EDC or camping purposes. After carefully reviewing the options available on Thingiverse, I was unimpressed with their flimsy construction. So, I decided to create something better myself. A major...

This is perfect for either everyday carry or camping adventures. After reviewing available options on Thingiverse, I was unimpressed by their flimsy construction, which is why I decided to create this alternative solution. ##Note: No raft or...

Made by request.

my first design in fusion 360. ...not the best but it works, contains the smell.

“This is Halloween, This is Halloween”

PALM - VORONOICompact, elegant and great feel.Haven't had one break in daily use.Also check out the original PALM.Secret compartment/Cigarette size:Even though it might not look like it, it houses a full self-rolled cigarette of 75mm height.

joint

joint

Joint

joint

JOINT-

SHAFT JOINT

Joint, marijuana joint, dak,cannabis cigarette,

Joint, marijuana joint, dak,cannabis cigarette,

this is joint