john mulaney stl 3d models

wwe head john cena .obj .stl

head of john cena peacemaker for custom figures .STL .OBJ

John is a 3D label displayed prominently in Arial Black font on a SketchUp model, labeled "John" in bold.

... or concerns about this model, please don't hesitate to reach out. I'll respond promptly and do my best to address any issues. In addition to John Cena's bust, I also offer a wide range of other celebrity 3D models that might be of interest to you.

Created using ZBrush, this highly detailed model captures Elton John's iconic look with stunning precision. I'm also including two separate versions: one featuring Elton John wearing his signature glasses, and another without them, so you can choose...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=340321 Instructions Using the following options: Block Width is set at 1 inch. I've named this creation JOHN. ... The Block Length has been adjusted to 10 units.

... ...To customize it further, use these settings: font - orbitron.dxf, font size - 10, message - John, stick width - 8, stick thickness - 3, flat bottom - 1, hole radius - 3, and font thickness - 5.

http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: Text = John twist = -3 Loop_x_position = 2 Loop_font = Chewy height = [5,6,4,5,4,3,5,4,6] Loop_character = o center = 60 spacing =...

... To create this, parameters were set as follows: font thickness of 3, stick thickness of 2, hole radius of 1.5, the 'Write' Orbitron DXF font for text, a message that reads "JOHN", stick width at 5, a flat bottom, and a font size of 10.

Below are instructions on how to use the custom options chosen for this version: **Using the following settings:** - Stick Width = 12 - Font Family: Orbitron (Font File: write/orbitron.dxf) - Displayed Text: John - Stick Thickness = 2 mm - Font...

... ...To personalize it, you can input your name as "John", enable flat bottom, set hole radius to 3, choose font thickness of 4, select the 'write/orbitron.dxf' font, set stick width at 8, font size of 10, and stick thickness of 3.

... ...To personalize it further, adjust these settings: create a holder (make_holder = 1), set text size to 10, establish a radius of 30, display the text as "John", set height to 20, and length to 35.

Detailed Directions Utilizing These Key Features: rotation of z Axis is set at -45 Degrees scaling in the z Direction reaches 35 Times the message as a Whole Shines Through With "john/johnson" Displayed Prominently movement along the x Axis amounts...

http://www.thingiverse.com/apps/customizer/run?thing_id=175150 Instructions Using the following options: fontsize = 8 line_spacing = 2 plate_thickness = 3 slitwidth = 4 font = write/orbitron.dxf slitlength = 12 corner_radius = 3 text_style = -80...

(http://www.thingiverse.com/apps/customizer/run?thing_id=52734) with specifications tailored for John. ...The options chosen include a flat bottom, font thickness of 7, stick thickness of 3, font size of 10, using the 'write/orbitron.dxf' font with a...

Here is John Fitzgerald Kennedy relief on medallion/pendant ready for 3D printing. I am attaching version with ring added and without, however would you like to print it. I am including obj and stl formats. The current scale is 65 mm x 65 mm x 12.5...

Here is John Legend bust 3D model ready for 3D printing. The model current size is 5 cm height, but you are free to scale it. Zip file contains obj and stl. The model was created in ZBrush. If you have any questions please don't hesitate to contact...

Here is John McCain bust 3D model ready for 3D printing. The model current size is 5 cm height, but you are free to scale it. Zip file contains obj and stl. The model was created in ZBrush. If you have any questions please don't hesitate to contact...

Here is John Travolta bust 3D model ready for 3D printing. The model current size is 5 cm height, but you are free to scale it. Zip file contains obj and stl. The model was created in ZBrush. If you have any questions please don't hesitate to...

Instructions Using the following options: Loop_position = 4 Font_name = Luckiest Guy Text = John spacing = [19,16,17,17.9,14.7,14.8,14.3,12.25,11.9] twist = 0 center = 0 Loop_character = u Loop_font = Chewy Rotation = 40 height =...

Instructions Using the Following Options: Outline Color is Gray Ruler Unit is Millimeter Font Size is Eighteen Points Border Width is Zero Points Text Thickness is Four Point Two Milliometers Bar Length Trim is Zero Point Border Color is Black Outer...

Using the following settings to customize the custom nameplate: Setting width of label to 60 pixels Round the edges of label by 3 pixels Set the height of text at 20 pixels Choose Acme as font style for label text Increase depth of label to 0.6 mm...

Using the options below, carefully adjust the settings as desired: * build_plate_manual_y: Set this value to 100 * build_plate_manual_x: Set this value to 100 * height: Specify a height of exactly 1.6 units * lip: Ensure a lip thickness of precisely...

Using the following options: font_outline_style = rounded lug_width = 5 line_spacing = 1.4 lug_style = plate lug_text_distance = 2 ruler_unit = 10 text_color = DarkRed glyph_coalesce_strategy = bar and glyphs inner_margin_width = 1...

Here is the John Fitzgerald Kennedy bust 3D model ready for 3D printing. The current size of the model is 5 cm height, but feel free to scale it as needed. A zip file containing obj and stl files is available for download. This highly detailed 3D...

A zip file containing both obj and stl files is attached for your convenience. Created using ZBrush, this model comes in two versions: one merged with glasses and another without glasses or separate glasses, giving you flexibility to print and...

Here is a bust 3D model of John Fitzgerald Kennedy ready for 3D printing, meticulously crafted with a current size of 5 cm in height but easily scalable to suit your needs. The accompanying Zip file includes both obj and stl formats, perfect for...

Pope John Paul II portrait 3d model STL file printable. The model is watertight, checked by different methods. There's no topological issues, flipped normals, etc. On the pictures you can see the model in different variations - based, no basement,...

A comprehensive zip file is included, containing both obj and stl files that are easily printable with any 3D printer. This exceptional model was meticulously crafted using ZBrush software, showcasing a level of detail and realism that is truly...

IF YOU WANT A JOHN CENA BUST WITH TEXTURE, IT'S RIGHT HERE: https://www.cgtrader.com/3d-print-models/miniatures/figurines/john-cena-bust-ready-for-full-color-3d-printing IF YOU HAVE ANY QUESTIONS OR NEED HELP IN A FLASH, DON'T HESITATE TO REACH OUT....