john mayer stl 3d models
315993 3d models found related to john mayer stl.thingiverse
Customized Version of Thingiverse Project: http://www.thingiverse.com/thing:1204005 Created with Customizer Tool: http://www.thingiverse.com/apps/customizer/run?thing_id=1204005 Instructions for the Project You are using the following customization...
thingiverse
www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following settings: Font thickness is 6 points Stick thickness is 4 units Stick width is 10 units Font size is 16 points The message reads "Mayer" Hole radius is 3 units...
thingiverse
Customized version of https://www.thingiverse.com/thing:3395463 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3395463
cults3d
Customized version of http://www.thingiverse.com/thing:739573 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=739573
myminifactory
A vivid likeness of Samuel Mayer, the patriarch of Joseph Mayer, comes alive on canvas. Born in 1767, he led a life marked by hard work as a skilled saddler and currier in Newcastle-under-Lyme. As his reputation grew, so did his entrepreneurial...
thingiverse
... Key settings used for this model include a hole radius of 3, enabled flat bottom, stick thickness and width of 1 and 5 respectively, font size of 12, displaying the message "Mayer 40er" using a font named write/orbitron.dxf with a thickness of 4.
myminifactory
Joseph Mayer's Portrait Relief Captures English Goldsmith and Collector Born to Samuel Mayer, a tanner and currier, Joseph Mayer made his mark as an English goldsmith, antiquary, and collector. At 20, he set up shop in Liverpool as a jeweller and...
myminifactory
Liverpool's Joseph Mayer amassed an impressive collection as a local collector and antiquarian; these treasures ultimately served as the cornerstone for the establishment of the Liverpool Museum.
myminifactory
This is an image portraying Jane Mayer, Joseph Mayer's sibling, standing steadfast as the guardian of his household from 1806 until her passing in 1892. ...The woman is adorned with a brooch that holds a cameo portrait of her brother Joseph, proudly on...
thingiverse
Stanley Mayer Fuel Cell utilizes 25mm and 18mm pipes. ...The key factor is to determine the optimal pipe length, but it's essential to note that using an 18mm pipe results in a 2.5 cm increase in height compared to other configurations.
thingiverse
This scaled representation of Adlet Mayer's sword from Rokka No Yuusha has been crafted with meticulous attention to detail. Approximately 94 hours were devoted to this endeavor, ensuring a maximum height of 65 cm is achieved. The design should...
cults3d
head of john cena peacemaker for custom figures .STL .OBJ
thingiverse
John is a 3D label displayed prominently in Arial Black font on a SketchUp model, labeled "John" in bold.
cults3d
... or concerns about this model, please don't hesitate to reach out. I'll respond promptly and do my best to address any issues. In addition to John Cena's bust, I also offer a wide range of other celebrity 3D models that might be of interest to you.
pinshape
Created using ZBrush, this highly detailed model captures Elton John's iconic look with stunning precision. I'm also including two separate versions: one featuring Elton John wearing his signature glasses, and another without them, so you can choose...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=340321 Instructions Using the following options: Block Width is set at 1 inch. I've named this creation JOHN. ... The Block Length has been adjusted to 10 units.
thingiverse
... ...To customize it further, use these settings: font - orbitron.dxf, font size - 10, message - John, stick width - 8, stick thickness - 3, flat bottom - 1, hole radius - 3, and font thickness - 5.
thingiverse
... ...To personalize it further, adjust these settings: create a holder (make_holder = 1), set text size to 10, establish a radius of 30, display the text as "John", set height to 20, and length to 35.
thingiverse
... ...To personalize it, you can input your name as "John", enable flat bottom, set hole radius to 3, choose font thickness of 4, select the 'write/orbitron.dxf' font, set stick width at 8, font size of 10, and stick thickness of 3.
thingiverse
Below are instructions on how to use the custom options chosen for this version: **Using the following settings:** - Stick Width = 12 - Font Family: Orbitron (Font File: write/orbitron.dxf) - Displayed Text: John - Stick Thickness = 2 mm - Font...
thingiverse
Detailed Directions Utilizing These Key Features: rotation of z Axis is set at -45 Degrees scaling in the z Direction reaches 35 Times the message as a Whole Shines Through With "john/johnson" Displayed Prominently movement along the x Axis amounts...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: Text = John twist = -3 Loop_x_position = 2 Loop_font = Chewy height = [5,6,4,5,4,3,5,4,6] Loop_character = o center = 60 spacing =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=175150 Instructions Using the following options: fontsize = 8 line_spacing = 2 plate_thickness = 3 slitwidth = 4 font = write/orbitron.dxf slitlength = 12 corner_radius = 3 text_style = -80...
thingiverse
... To create this, parameters were set as follows: font thickness of 3, stick thickness of 2, hole radius of 1.5, the 'Write' Orbitron DXF font for text, a message that reads "JOHN", stick width at 5, a flat bottom, and a font size of 10.
thingiverse
(http://www.thingiverse.com/apps/customizer/run?thing_id=52734) with specifications tailored for John. ...The options chosen include a flat bottom, font thickness of 7, stick thickness of 3, font size of 10, using the 'write/orbitron.dxf' font with a...
cults3d
Here is John Travolta bust 3D model ready for 3D printing. The model current size is 5 cm height, but you are free to scale it. Zip file contains obj and stl. The model was created in ZBrush. If you have any questions please don't hesitate to...