jk ipad dash mount 3d models

... (potentially more, see the photos and try to figure out if it will fit for you) above the rearview mirror, where a sunglasses clip typically goes. ...Enables the mounting of Dash cameras for States where dash cams aren't allowed on the windshield.

To attach an iPad Mini in landscape mode on a Sole elliptical trainer and enjoy Netflix during exercise, print the mount using Makerbot Replicator 2 at standard resolution with 30% infill.

This is a mount for my MacBook Pro 14" and my iPad 8. Gen. I use it as Sidecar Display. ... It is a little bit critical for the stability of the display, but it works...

Ideally the main portion of this bracket would be printed in one piece; however, for many print beds a 10.2" iPad mount must be printed in two parts to fit. A small stabilizer/connecting brace is included, solidifying the two halves. ...Gluing the two...

This device is a sturdy wall bracket designed specifically for mounting the 2014 iPad Air 2. ...To ensure a precise fit, some users may need to carefully sand down the cable hole using a file to create a seamless connection.

The goal is to modify this design to attach an iPad Air Waterproof Lifecase to a Standard RAM Mount Hex Button (RAP272) using two #8 Pan Head Screws. To maximize its strength, print it with a C profile on the bed where mounting holes are...

A mount to attach an iPad Air to a din rail You can read about the project at HTTPS://www.instructables.com/A-Simple-Magnetic-Ipad-Stand-for-a-Lazy-Night-of-N/ You will need to print two tabs for this design. ... They can be found at:...

The iPad 1 and 2 are slightly thicker (1.5mm or so) than the 3 and 4 so the original mount does not work for them. I extended the slot size so it works for the 1 and 2 versions. The picture I took is missing the bottom right clip because my...

It can even slide under a shiplap "nickle gap" just right to mount on a wall without screws (Mount upside down) XD *Slides under dash trim** **Similar to : https://www.thingiverse.com/thing:3487884** Enjoy!! ... **4/2/21 Added QuickShade V2** ...

I started searching for an iPad car mount that fit my exact needs but couldn't find one, so I decided to design one myself using Fusion 360. This custom mount fits snugly around the headrest posts of a Toyota Sienna (2015 model) and is specifically...

... Layers for Top and Bottom with 2 each. Opt for a Honeycomb Infill with a moderate density of 20%. Activate Support Generation to ensure stability. Now, place your ASUS Nexus 7 tablet within the double DIN car dash mount for seamless integration.

This is a dash mount holster for a Smith and Wesson M&P 380 EZ M2.0 the print is articulated for easy printing. No supports needed. 50% infill is solid as a rock. ...

... at 1.6 seconds per layer. Once cured I spray painted it with a satin black, and it blends right in. The mount snaps onto the mirror stem solidly, but is readily removable, and the dash cam is removable just as with the originally supplied mount.

To maximize its usability, however, the iPad would need to be placed out of the way, ideally mounted on the wall. I created this design to meet her needs, and I must say I'm really impressed by how seamlessly the iPad fits into it. ...In fact, Apple...

This design has countersunk holes for magnets and a string hole, making it compatible with the original Magnetic iPad Mount while adding extra security against accidental dislodgement. However, note that it requires support during printing. If you...

I'm redesigning my tablet wall mount again, this one tailored specifically for an iPad Air, although it should fit any other iPad without a case attached. Besides providing a snug hold and a slim edge so it doesn't block any screen real estate, this...

... power button. The parts to connect both parts together are a little bit smaller as well, but still needed some work to fit perfectly. I did not change the brackets which do not fit the iPad 6 perfectly, but good enough to hold the ipad in place.

I'm having serious trouble finding a tripod mount that can handle the weight of my 12.9" iPad Pro during long time-lapse photo shoots! To solve this problem, I designed and built a custom holder that securely fits my iPad even when it's wrapped in...

This is my iPad Mini 4 wall mount to use home assistant. Its a slide system so you can take the ipad and use it like normal. This is the 90 degree cable i used. ... https://www.amazon.co.uk/dp/B091KGZ4Z2/ref=cm_sw_em_r_mt_dp_7P6EG8TTR2GTEWJ0SKV6 I...

If you are using SideCar or Duet Display with iPad, you might want to mount your iPad onto your MacBook. There are some tools to do that available in the market. This 3D printable object helps you achieve same thing. It has 2 hinges which allows...

I needed a cell phone mount specifically designed for my new S7, and since my Ram Truck's dash has a useless pocket on top, I created this custom solution that can be either screwed or glued into that spot without obstructing the radio or AC vents. *...

Measure the object in question and change the parameters of the wall_mount() function in the source file to generate new models with OpenSCAD.Example STL:s are attached for two different remotes, and also an iPad 4 mount which is used for our home...

I utilize this specifically to secure my iPhone 6S Plus with a Defender case within my Jeep JK.

A customized version of http://www.thingiverse.com/thing:584209 was created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=584209 Instructions are as follows: To make it work, choose from the following options: Chest...

The adjustable arm on this mount provides flexibility in terms of positioning the iPad Air 3 at the perfect viewing height for comfortable reading or watching movies. ...The durable construction and sleek design make it an ideal accessory for any room...

Installation Notes ----------------- • Use 3M mounting tape to attach this to the dash. • Clean the mount and dash with alcohol before applying 3M tape. • The throttle controller mount will attach to the side that has HIKEIT printed on it. Buy...

Wall Mount for the 2018+ iPad Pro 12.9" This mount holds your iPad flat against the wall, freeing up valuable surface space while keeping it charged and ready to go. To secure the mount to the wall without using screws, apply 3M Command Strips to...

Mount for FZero Dash so it can be mounted and used on a simucube 2 (sport). ... This version is created so you can use it with magnets (Ø10mm x 5mm N52) to mount it to the wheelbase to take it on/off easier without removing the complete screws of the...

I bought on Amazon a mount for an iPad on a tripod and the 1/4" screw did not fit completely in the mount (not deep enough). ...I designed a disk with the right dimentions in order to ovecom this problem with success.

To utilize this adapter, I created a mounting plate that seamlessly integrates with my own 3D-printed iPad mini 4 sunshield, which can be found on Thingiverse under the ID #2803081. On September 28th, 2018, I updated the design to include an...