jim parsons model

Get the entire plow here: https://cults3d.com/en/3d-model/various/scx6-plow I have designed this plow for the SCX6. The blade reaches a size of 15.5 (394mm) wide. This does limit a print to some bed that have a 400mm build value. However, I have...

The cookie cutter designs are partly based on 3D models from our [3D museum](http://sketchfab.com/NHMWien) and were designed by Viola Winkler. The scan team of the NHM Vienna wishes you a wonderful holiday season, lots of fun baking cookies and a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 7 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

These are not proper, but I didn't care for a test model. Most likely you will need to ream the holes for the motor shafts. I used a 5/64" drill and very carefully reamed the hole at a low speed. This creates a hole with a .0006" press fit. I do not...

... absolutely know what you are doing. Acknowledgements: Thanks to Rick and Morty, who posted this wonderful ASX1 model on grabcad, which I used as the basis for my renders. ... https://grabcad.com/library/artillery-sidewinder-x1-1

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 0 stencil_shape = 4 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

The basic general thickness of 1.67 mm should work with most plastics.Orientation: Side on printing bedTo make sure that the weight of whatever you put in the hook is pulled by the material itself and not the layer lines, my hook should always be...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

The initial idea was to couple the two 4020s to the original TTBluer case, however it has lower flaps that made the process difficult, as I wanted to preserve the original part without cutting flaps, I decided to model a new case. I have results...

After the actual print of the model has started the control switch can be quickly flipped to the Auto position to enable the auto power off of the printer at the end of the print.  If at any stage you wish to disable the auto off function, simply...

To do this I went to https://3dp.rocks/lithophane/ sized it in model settings, and set it to Positive under image settings. I kept it flat since it will be used as the back of the bookstand. But while it's not in use it can also be used as a cool...

I built the flat surface of the skirt with ParametricPlot3D, then intersected it with a lattice-like model, then I utilized those tables to make two ParametricPlot3D tubular surfaces, which I then pieced together using the Show command to make the...

... screws into the bottom of the mount, adjusting the position so the drive is flush with the front face. That's it! I've only tested it on my PowerSpec branded Lancool 205 Mesh case, but it may be possible to use it with other case models as well.

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: crankSlack = 1.8 times smaller gear_tolerance = a negligible 0.1 inch midAxisHolderH = stands at an impressive height of 6.3 inches noteAlpha =...

Scaling: The model as is in the STLs will accommodate most types of earbuds, however it can be scaled down as much as 30-35% for smaller sets. If you use earbuds with an inline control, such as the ones shown in the pictures, the standard STL size...

The little hills on the model are great for providing a little friction on the bottom of the phone too. Day 16 | MST3K Ornament | Inspired by the TV show turned Netflix remake, This print is quick, easy, and a great conversation starter. Day 17 |...

This would not work on a single nozzle printer, so we opted for truncated tetrahedra with slight insets on two of their triangular faces. INSTRUCTIONS Everything prints at 0.2 mm layer height.Set your line width to 0.45 mm, as the pattern...

Great model from bendansie. Remixed to support free. Print with the Bearded Yell : https://www.thingiverse.com/thing:4561831 <iframe width="560" height="315" src="https://www.youtube.com/embed/HCxeydgMAGE" frameborder="0" allow="accelerometer;...

Parts description This printable model is made of 4 parts: Casing: this is the central part, the thick ring with a partially-closed wall on one side. Inner ring: a thin ring used as part of the locking mechanism for the petals. This part must be...

Print Settings: - Printer Brand: RepRap - Printer Model: Prusa i3 - Rafts: No - Resolution: 0.2mm - Infill: 30% Notes: 1st Part to Print: "Bottom Mount" This part doesn't require any support material. It's the most complex print in this design,...

For now I have modelled two trailers:mk14 flatbed trailer for general loads, 10' and 20' ISO containers.mk17 tray-style trailer with hydraulic crane. Can carry 1x 10' ISO container, or general loads. Tray sides are removable.mk14 trailer can also be...

I'm no design expert, and 3D modelling makes my brain hurt. However, with a lot of perseverance, a set of calipers, hundreds of edits and redesigns, dozens of test prints, I have made a replacement ring battery. You will need the following: *...

This print allows to elegantly mount your Bosch eBike Charger to the wall, out of the way, right where you need it. I made this version because several people indicated that they liked my eBike Charging Station but preferred a standalone version of...

The extra space available in a Volcano setup would allow much more open channels and sweeping paths, and I would like to improve the Volcano version in future, but this will require significant modelling work which I just don't have time for at the...

There you can find links and reviews about quality hobby products. https://MyHobbyTools.com ✔ 3D PRINTING My Favorite 3D Printers 3D Printing Tools 3D Printer Parts ✔ ELECTRONICS Batteries and Chargers Soldering Kits & Modules Multimeters...

For square tubes of other sizes (including non-20-mm), see Section 7.1 “Fusion 360 design parameters” for model modification. - All idler pulleys (toothed & smooth, 16T & 20T) combinations are provided with corresponding carriage variants. - Both...

  Walmart also has a good deal on a 4 Pack of the same filters HERE.The fan is a Black & Decker 9in Mini Box Fan, Model BFB09W.CostAt the time of writing this the total cost is the same for each of the 3 versions as the different sized filters are...

useful as an object holder (Elettronics component, Dyn, various tools, modellism, cutting and sewing, make-up set, manicure, fishing ... etc https://youtu.be/w3FsHNZxC64 Description The chest of drawers is made up of five containers with single...