jgmaker magic 3d
1747804 3d models found related to jgmaker magic 3d.thingiverse
This is a replacement fan shroud/air duct for the 3D magic. It works. Tight fit. Slightly less directional area then the stock air opening, but slightly faster air too. About 2 millimeters of clearance around the hotend for both nozzles. Could...
cults3d
I have created custom firmware that enables the use of the BLTouch and clones on the JGMaker Magic 3D Printer but it does require board modification to add pins to connect the probe to. ...If enough interest here I will edit and add the link to the...
thingiverse
I have created custom firmware that enables the use of the BLTouch and clones on the JGMaker Magic 3D Printer but it does require board modification to add pins to connect the probe to. ...If enough interest here I will edit and add the link to the...
thingiverse
This is a Slightly improved Part Cooling Duct for the JGMaker (JGAurora) Magic 3D Printer. ... Basic improvements over the stock duct include: + 3mm separation from the heater block so its doesn't melt like the original + air flow directed better to...
thingiverse
Adapters for installing the SKR 1.3 Mainboard into the JGMaker Magic 3D Printer. There are some required modifications to the JGMaker Magic's wiring to use any standard mainboard in that printer. The factory mainboard from JGAurora uses non-standard...
thingiverse
Like many others, I too was facing challenges in printing TPU using my Bowden extruder, specifically a JGMaker (JGAurora) Magic 3D printer. Initially, I used thing:3485470 for the Ender 3, but required re-rendering to adjust the feed hole height,...
thingiverse
This is an upgrade fan shroud for the Jgmaker Magic to accommodate 40mm fans. I have tested this with both a regular heat block and a volcano heat block and got great results. I was able to achieve a clean overhang test up to 80% before it got...
cults3d
This is an upgrade fan shroud for the Jgmaker Magic to accommodate 40mm fans. I have tested this with both a regular heat block and a volcano heat block and got great results. I was able to achieve a clean overhang test up to 80% before it got...
thingiverse
Direct Extruder for JGMaker Magic and Z Axis Bearing Need: printed Parts T Nuts and Screw BMG Dualdrive Extruder Stepper like 17HM08-1204S (42x20) Bearing 14x8x4 Cableholder and Filaholder infill 25% direct extruder and z-bearing infill 100% *works...
thingiverse
I mirrored the original to match the mounting screws on my power supply as well as making the model a bit shorter to match the clearances underneath the JGMaker Magic. I also noticed the preinstalled fan screws on my power supply had a narrow...
thingiverse
This is a Upgrad for the JGMaker Magic for a 4010 Coldendfan and for a 4010 or a 5015 Blower for Part cooling. Needed Screws and Nuts. ... For 4010_Blower Bulid: Screws - ISO4762 M3x6 - 7 M3x10 - 2 M3x16 - 2 M3x20 - 2 Nuts -...
thingiverse
These are brackets for a Y-axis drag chain on the JGMaker Magic. ...they are compatible with the drag chain by @diogosantos88 https://www.thingiverse.com/thing:3715002
thingiverse
Modified the E3P/CR10S HMG7 gantry carriage adapter to fit the much smaller and minimalist gantry carriage of the JGMaker slash JGAurora Magic, as well as made a vertical mount for the hotend breakout board so that everything still works as designed....
thingiverse
This is a dual outlet fan duct I remixed from the one sirhcwolf had created to work with the fan shroud I created for the JGMAKER MAGIC. ... My fan shroud can be found here: https://www.thingiverse.com/thing:4426539 sirhcwolf's single duct can be...
thingiverse
These are two types of filament sensor adapters for the JGMaker Magic using a Bondtech extuder so that the filament sensor lines up properly with the filament entry hole of the Bondtech extruder. ... Please refer to my YouTube Video on how to install...
cults3d
This is a dual outlet fan duct I remixed from the one sirhcwolf had created to work with the fan shroud I created for the JGMAKER MAGIC. ... My fan shroud can be found here: https://www.thingiverse.com/thing:4426539 sirhcwolf's single duct can be found...
thingiverse
Dual 5015 fan duct for the JG Maker Magic. ...Works with stock shroud and https://www.thingiverse.com/thing:4426539
thingiverse
**AGAIN**, making these modifications to your JGMaker Magic 3D Printer WILL Void its Warranty I also posted a YouTube video explaining the changes along with audio demonstration of the decrease in noise to the printer. Silent Magic:...
cults3d
Support for Auto Bed Leveling Sensor for JGAurora JGMaker Magic
thingiverse
Remix @Waggster's design. ... Remove spool holder screw holes, make a new craw that can be attach to guide rail.
thingiverse
This was inspired by https://www.thingiverse.com/thing:4541909 as a start, but I wanted to improve rigidity as well as its stability. With a ridge in the back against the metal shell, it can no longer rotate. Mounting instructions: Read...
thingiverse
The ingenious inventor carefully constructed a mesmerizing device that could transform ordinary objects into extraordinary marvels of modern science.
thingiverse
You can make your JGmaker magic a direct extruder, and even mount BLtouch. The taitan extruder is perfect for this mounter. You can also mount BLtouch, but you need to change the motherboard or add parts. I replaced it with SKR mini E3. ...
thingiverse
You can make your JGmaker magic a direct extruder, and even mount BLtouch. The BMG extruder is perfect for this mounter. You can also mount BLtouch, but you need to change the motherboard or add parts. ... I replaced it with SKR mini E3.
thingiverse
There are two adapters for direct extruder. ...The white one is a simple version(v1.0), the red one(v5) is a stronger version and better for BMG extruder.
cults3d
Direct drive Mount for Mosquito and BMG extruder for JGAurora JGMaker Magic, Blower 4020 You have to build a new V Slot Plate without the pins for heatsink, that the original brings with.
thingiverse
A shroud upgrade for the Jgmaker Magic extruder shroud. It fits on the original gantry and uses the original extruder pcb. It uses a 4010 fan for the heatsink fan with a stealthburner style mounting system and two 4010 blower fans for the part...