jgmaker artist d 3d models

... filament. ...I allows you reproducibly measure and cut small lengths of PTFE tubing for the JGMaker Artist D nozzles. ...This will allow you to upgrade tubing to higher spec material or even just replace a bad tube.&nbsp;</p><p>PLA or PETG.&nbsp;</p>

I used the 24v slot rail strip from PrinterMods, but had to lengthen the wire by about 2 ft. I tucked my wires under the blue plastic strip that houses the filament runout wiring. Print Settings Printer: JGMaker Artist-D Pro Rafts: No Supports: No...

Will add one for Pro with 2040 top bar replaced if someone can get me some dimensions. Hardware: knob: #5 x 30 mm hex bolt, washer and nut, and #5 x 16 mm bolt &amp; nut. no knob: #5 x 20 (or 25) mm hex bolt, washer and nut, and #5 x 16 mm bolt...

I bought a dial indicator from Harbor freight to precisely set the z height of the 2nd extruder on a JGmaker artist-D pro. I made a base to hold the indicator upside down so I can indicate the nozzles. (ie set indicator to zero on E1 then adjust E2...

You can create an extension wire for your runout sensor: 2PIN Female and Male Connection Plugs on Amazon Print Settings Printer: JGMaker Artist-D Pro Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: eSun PLA or PETG Purple Notes: Use...

There are two optional #3 holes should you decide to drill into your case. Bed mount: two #3x12mm screw, nut. Links: 10x10 chain on Amazon. 10x11 open chain on Amazon. Print Settings Printer: JGMaker Artist-D Pro Rafts: No Supports: Yes...

A RunOut Sensor holder for the Artist-D Printer, to fit on the extruders.

This is a replacement part for the Artist-D air duct. Its design is based on the original part the printer ships with. This is the air duct for extruder 1. ...If you need a replacement for extruder 2 simply mirror this part.

Purge bucket system for Artist-D, the open bucket comes from somebody else, but I have included it all here. I have made a receiver the fits on each side of teh printer. You will need to print 9 to 10 spacers. ...On mine, 5 where used on the right side...

Quick and easy indicator mount I made for getting a flatter bad on my Artist-D. No supports necessary. Uses a quarter inch nut and bolt to fasten the indicator to the mount. The mount locks into the grooves that are cut into the stock steel shell for...

Designed for the Artist-D IDEX printer. Bracket mounts spool for perpendicular filament feed into the sensor and direct drive. ... Use with Filament Holder https://www.thingiverse.com/thing:3020026

Designed for the Artist-D IDEX printer. ...Bracket mounts spool for perpendicular filament feed into the sensor and direct drive.</p><p>Use with Filament Holder https://www.thingiverse.com/thing:3020026</p>

There are 2 versions of mount for the Octopus in the Artist-D Mount 1 is internal (no cutting required) and holds a Pi 4 as well as the Octopus. Mount 2 puts the I/O of the Octopus against the Artist-D case, I cut out a hole to make this fit nicely...

Update 2/26/2022: Added (not tested) mount for the base Artist-D (non-pro). If there's a problem with it, let me know and I'll update it. Also have a 2 mm spacer, if needed, to drop the bucket. Just change the height in your slicer if you need a...

Mount for EZ Cam to mount to the Artist-D Pro. It attaches to four screws on the left side of the machine. You will have to get 4 screws - M4x16. ... The original screws were only 12mm long, and they did not reach The holes are notched out to allow a...

Pour information, j'ai déconnecté et démonté l'écran tactile de mon Artist-d Pro pour installer un LCD12864. J'ai pu upgrader en Marlin 2.0.7.2 et profiter de toutes les options disponibles (sauf le mode UART). Offset X = 17.2 Offset Y = 21.4 ...

UPDATES; If you intend to use your Artist-D at ABS temperatures, you will need to print these parts in ABS as well. PLA and PETG will deform at ABS temperatures. With this in mind, I have added a new single piece RIGHT mount (v8) that works better...

These mount two (non mirrored work fine with these), BMG direct drive extruders to the existing Extruder plates on the Artist-D. These have been through a few iterations, and i have updated these models with the final tweaks I needed to do to my...

These mount two (non mirrored, no idea if mirrored would work ok with these), BMG direct drive extruders to the existing Extruder mount plates on the Artist-D. These have been through a several iterations at this point, mostly part cooling...

Since I already needed to elevate my printer because of fan replacement, and because other solutions did not fit this printer, I decided to make bespoke feet for my Artist-D. The solution consists of two sets of springs for front/back feet (A/B)...

... 2. ...It allows adjusting the second extruder using the stock mechanism. It fits perfectly to BigDogMakes Artist-d Hemera Mount. I use it with Trianglelab Matrix extruders. Hint: Use some longer M4 screws. One m3 insert nut is needed. ...

... for extruder 2. ...It allows adjusting the second extruder using the stock mechanism. It fits perfectly to BigDogMakes Artist-d Hemera Mount. I use it with Trianglelab Matrix extruders. Hint: Use some longer M4 screws. ...One m3 insert nut is needed.

I had y-axis issues with my i3 Mega that were fixed by Todd Lowe's tensioner, so when I had similar trouble with my Artist-D and the y-axis was so similar, it seemed like a good place to go. I was half-way done designing it from scratch when I...

... rest of the holder directs the air from bottom to the side, restricting its "leak" back into the case. I made this holder before I gave up on the "all fan replacements must be inside". Now I'd simply mount a single 120mm fan and be done with it.

I have a new design that I'm running on my Artist which I'll probably add a remix for (bltouch closer to nozzle (reduced offset = more reliable probing) and 5015 fan incorporated into body to unobstruct the view of the nozzles). I therefore won't...

I have a new design that I'm running on my Artist which I'll probably add a remix for (bltouch closer to nozzle (reduced offset = more reliable probing) and 5015 fan incorporated into body to unobstruct the view of the nozzles). I therefore won't...

Upgraded with tab to stop it from twisting left and right when the nozzle runs over the brush. ...May or may not need spacers (I used two)

updated this design to add a middle support to strengthen the slots holding the BL touch. I have yet to print or even buy a BL touch. ... This effort is still in progress

Modified BMG mount to allow for ease of lining up the PTFE tube when you swap out a nozzle. ...Needs to be mirrored in slicer for E2.

Fan (40x40x20) Mount for JG Maker Artist D Pro